Page 25 of 46 FirstFirst ... 15232425262735 ... LastLast
Results 241 to 250 of 452

Thread: 2 fast 2 fat

  1. #241
    Senior User mowgli's Avatar
    Join Date
    Apr 2002
    Location
    somewhere in the 80's, hinckley
    Posts
    35,194
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Buy a centre punch.

  2. #242
    Club Member turbojolt's Avatar
    Join Date
    Jan 2007
    Location
    derbyshire, derby, shelton lock
    Posts
    10,358
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    im look at a set from toolstation right now, want some before i start messing about mounting the seats
    ^^^ did you just read that? what a idiot ^^^


    PROJECT 2 FAST 2 FAT clicky


    ''lifes what happens, while your busy making plans''

  3. #243
    Club Member turbojolt's Avatar
    Join Date
    Jan 2007
    Location
    derbyshire, derby, shelton lock
    Posts
    10,358
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    bough a bench vice, only a small one but mehhhh



    started bolting some body panels back on to check my paint lines & line up where the bonnet pins are going



    now is it normall to see this gap under the bumper



    im going to remove the bumper irion and hold it on with bonnet pins, and leave the 2 screws either side to make sure its lined up half right atless, also thinking about getting a square licence plate for the corner and drilling holes in the bumper to get more air on the rad
    ^^^ did you just read that? what a idiot ^^^


    PROJECT 2 FAST 2 FAT clicky


    ''lifes what happens, while your busy making plans''

  4. #244
    Senior User
    Join Date
    Sep 2008
    Location
    Bridgwater
    Posts
    12,248
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    gap is normal mate

  5. #245
    Senior User Liam's Avatar
    Join Date
    Aug 2010
    Location
    Margate, Kent
    Posts
    2,121
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Instead of getting a square plate, get a stick on one and stick it on the bottom valance either in the middle or to one side.

  6. #246
    Club Member turbojolt's Avatar
    Join Date
    Jan 2007
    Location
    derbyshire, derby, shelton lock
    Posts
    10,358
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Liam View Post
    Instead of getting a square plate, get a stick on one and stick it on the bottom valance either in the middle or to one side.
    i like that idea,
    ^^^ did you just read that? what a idiot ^^^


    PROJECT 2 FAST 2 FAT clicky


    ''lifes what happens, while your busy making plans''

  7. #247
    Club Member turbojolt's Avatar
    Join Date
    Jan 2007
    Location
    derbyshire, derby, shelton lock
    Posts
    10,358
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    today i done this





    which has resulted in the bonnet looking like this



    whoopsieeeee

    this is where Ive placed the front bonnet pins



    wish i placed them further into the corners like every one else, that way they would have been square with the top ones I'm also putting in (isn't hindsight a lovely thing ) never mind this is only a stand in , eventually i will swap it for a fiberglass one and properly use locking bonnet pins

    also im going to buy panel beating hammer to flatted out some of the creases in the bonnet and then wrap it to make it look a bit less battered
    ^^^ did you just read that? what a idiot ^^^


    PROJECT 2 FAST 2 FAT clicky


    ''lifes what happens, while your busy making plans''

  8. #248
    Senior User mowgli's Avatar
    Join Date
    Apr 2002
    Location
    somewhere in the 80's, hinckley
    Posts
    35,194
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    sorry, but what the hell did you take the bonnet frame off with, a spade?

  9. #249
    Club Member turbojolt's Avatar
    Join Date
    Jan 2007
    Location
    derbyshire, derby, shelton lock
    Posts
    10,358
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    bolster



    it was full of dinks and dent when i got it back anyway so wasn't being to carefully tbh
    ^^^ did you just read that? what a idiot ^^^


    PROJECT 2 FAST 2 FAT clicky


    ''lifes what happens, while your busy making plans''

  10. #250
    Senior User pie's Avatar
    Join Date
    Jan 2009
    Location
    Blackwood gwent South Wales
    Posts
    6,769
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    f mowgli

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •