Search:

Type: Posts; User: Iain; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    147
    Views
    6,360

    The ecu will have most if not all. Which is why...

    The ecu will have most if not all. Which is why people are referring to the old ecu.

    It's just a case of finding the right wire and connecting it up to that plug. Mix of knowledge, Haynes and...
  2. Replies
    3
    Views
    89

    Not done it but I'd expect to add rack to the...

    Not done it but I'd expect to add rack to the list.

    Intersted in a photo of the bulkhead! I can't picture if they're symmetrical or not
  3. Replies
    1
    Views
    29

    Given the age of any Nova or XE hoses now, I'd...

    Given the age of any Nova or XE hoses now, I'd thoroughly recommend a silicone hose kit that's designed for a Nova+XE combo.
  4. Thread: Nova vxr info

    by Iain
    Replies
    4
    Views
    139

    I'm sure someone was building one in the projects...

    I'm sure someone was building one in the projects section. Can't remember a name though
  5. Thread: Saloon wings

    by Iain
    Replies
    3
    Views
    48

    PMd

    PMd
  6. Thread: Saloon wings

    by Iain
    Replies
    3
    Views
    48

    Where abouts are you?

    Where abouts are you?
  7. Replies
    312
    Views
    27,855

    Too cool. Keep it updated even with the lack of...

    Too cool. Keep it updated even with the lack of Nova content!
  8. Replies
    147
    Views
    6,360

    Lovely job. Surprised you're not removing those 2...

    Lovely job. Surprised you're not removing those 2 bits from the bulkhead, only a few bolts?!
  9. Thread: C20LET plates

    by Iain
    Replies
    2
    Views
    68

    A lot of people need extra room on crossmember...

    A lot of people need extra room on crossmember too for fmic. Perhaps look at a custom one of those too
  10. Thread: C20LET plates

    by Iain
    Replies
    2
    Views
    68

    Strengthening plates? Stitch welding minimum,...

    Strengthening plates?

    Stitch welding minimum, full rally style plating kit is probably recommended.
  11. Replies
    8
    Views
    158

    You suck at eBay ...

    You suck at eBay

    https://www.ebay.co.uk/itm/Vauxhall-Floor-Grommet-Nova-Corsa-C20XE-C20let-Sport-Rally-Gsi-Gte/184536450232?hash=item2af73ac4b8:g:ExkAAOSwsLdfqbI0
  12. Replies
    8
    Views
    158

    I think they're all the same bar one in the boot...

    I think they're all the same bar one in the boot that has a hole. Same as a Corsa B I think. You could get them from Vauxhall not too long ago but was quite costly for a cars worth - don't know if...
  13. Replies
    147
    Views
    6,360

    I liked it up to the point you applied the seam...

    I liked it up to the point you applied the seam sealer. Why not mask either edge and use a brush for a factory look?
  14. Replies
    4
    Views
    123

    So should be able to test sensor resistance No...

    So should be able to test sensor resistance

    No idea how to test the gauge, probably not with a multimeter, you need to mimic the sensor output with a fancy gizmo.
  15. Replies
    4
    Views
    123

    Pretety sure you can measure resistance on the...

    Pretety sure you can measure resistance on the sensor to test it.

    And in theory spoof the input into the clocks if you have the right equipment
  16. Replies
    2,133
    Views
    235,717

    Slap a Nova plate on it and just MOT it.

    Slap a Nova plate on it and just MOT it.
  17. Replies
    2,133
    Views
    235,717

    Looks badass. Always fine they look cooler in...

    Looks badass. Always fine they look cooler in this mid build phase than finished.
  18. Thread: Arp rod bolts

    by Iain
    Replies
    4
    Views
    119

    Highly doubt it. Pretty sure ARP won't be fond of...

    Highly doubt it. Pretty sure ARP won't be fond of trying to lash together second hand sets of bolts.

    Have you measured them to see if they're still in tolerance?
  19. Replies
    147
    Views
    6,360

    I've never had a bender too, hammer and vice...

    I've never had a bender too, hammer and vice works for most things. Recently bought a little vice mounted 5" or so bender for little brackets and such which is quite nice.
  20. Replies
    147
    Views
    6,360

    Impressive if that's your first attempt at making...

    Impressive if that's your first attempt at making repair panels. I'd be well chuffed if I'd done that!
  21. Replies
    166
    Views
    15,845

    I like the idea of drilling out the clutch nylon...

    I like the idea of drilling out the clutch nylon and adjusting via a nut. Much easier!
  22. Replies
    12
    Views
    247

    White looks badass the first MOT you put it on...

    White looks badass the first MOT you put it on the ramp. Just impractical if you plan on using and abusing it and expect it to look nice.

    Going black would mean no top coat of paint, which could...
  23. Replies
    12
    Views
    247

    Based on the pics and link above it looks like I...

    Based on the pics and link above it looks like I went over partially painted + sealed surface with the POR15. Rusty metal it's great on, but a good key I've found is enough for it.

    Yeah I did use...
  24. Replies
    12
    Views
    247

    I did actually prime, stonechip (aerosol) and...

    I did actually prime, stonechip (aerosol) and Hammerite the underside, but it was brittle so I took it all off agian, hence the patchyness. I left the seam sealer on from the original bad attempt...
  25. Replies
    12
    Views
    247

    On mine I did the following: Wire wheel on...

    On mine I did the following:

    Wire wheel on grinder back to metal OR the original cream coating
    Keyed
    POR15 paint everywhere
    Seam sealer where necessary
    3M stonechip
    2K paint with a brush
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4