Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: 1300sr nova bits

  1. #1
    Newbie
    Join Date
    Sep 2015
    Location
    North East
    Posts
    7
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default 1300sr nova bits

    Nova parts for sale,


    Some of these parts came off my old autograss car and are a bit grubby, some parts were just spares and have never seen the track. If you are interested then email or reply to the thread.
    Thanks


    1 x 1300sr bare block – offers
    1x set of 1300 rods with pistons still attached (no big ends) – offers
    1 x 1300sr complete bottom end made +40 with oversized pistons (markings on pistons are v 1.00) has been used as my race engine so will need a clean + possible new rings. Is connected to an F10 box, or can come on its own. - £100


    1 x f10 box very grubby had as spare, been sat in the garage for a few years.


    1 x standard 1300sr head, all there, valves/springs/lifters/cam etc


    1 x slightly ported and polished 1300 cylinder head (just valves and valve springs no cam or cam carrier.


    1 x 1300sr cam in cam carrier with rocker cover


    1x sr bumper, never seen the track, few bumps and scrapes off a road car
    1x rear sr bumper never seen the track few bumps and scrapes


    1x e-tec front strut brace


    1x boot with glass, still has wiper motor, poor condition
    1 x bonnet off road car poor condition


    1 x set of genuine gm sr/gsi 3 spoke 14 inch alloys, never seen the track, in good condition, too good to race, few dings and bangs, never had them on a car, no centre caps or tyres




    Cash on collection, open to offers on the bits, there are other small bits and pieces. They have all been sat in the garage for the past few year though and will all need a clean and may not be in a1 condition. Message if unsure. Parts can be collected from Harrogate or Whitley Bay. I cannot post any.

  2. #2
    Junior User
    Join Date
    Jul 2014
    Posts
    80
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Hi, is the ported/polished head suitable for a 1200 performance block ? Also is the front bumper mk2 ?

  3. #3
    Senior User mowgli's Avatar
    Join Date
    Apr 2002
    Location
    somewhere in the 80's, hinckley
    Posts
    35,194
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by NormanNova View Post
    Hi, is the ported/polished head suitable for a 1200 performance block ? Also is the front bumper mk2 ?
    it would fit a 12ST block with no trouble. the c12nz thing would be more trouble with the smaller bore size

  4. #4
    Newbie
    Join Date
    Sep 2015
    Location
    North East
    Posts
    7
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Bumper is sold sorry

  5. #5
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Able to send pictures of the standard head and cam/carrier?

  6. #6
    Junior User
    Join Date
    Jul 2014
    Posts
    80
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    How much for the head then mate ? And how do I tell which engine I've got ?
    Would you know If I say it's a 1991 mk2 1.2 saloon ? Cheers

  7. #7
    Senior User mowgli's Avatar
    Join Date
    Apr 2002
    Location
    somewhere in the 80's, hinckley
    Posts
    35,194
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Has it got a choke or not?

  8. #8
    Junior User
    Join Date
    Jul 2014
    Posts
    80
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Yes it has manual choke

  9. #9
    Newbie
    Join Date
    Sep 2015
    Location
    North East
    Posts
    7
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by leggattr View Post
    Able to send pictures of the standard head and cam/carrier?
    Having trouble sending pictures without them being massive. I can email them, if you PM me your email address?
    Cheers

  10. #10
    Newbie
    Join Date
    Sep 2015
    Location
    North East
    Posts
    7
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by NormanNova View Post
    How much for the head then mate ? And how do I tell which engine I've got ?
    Would you know If I say it's a 1991 mk2 1.2 saloon ? Cheers
    Make me an offer mate, I can get pictures on the weekend. Please note as far as I can tell it is polished and lightly ported, It was deemed illegal for my formula of racing, cam carrier is separate to the head

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •