Search:

Type: Posts; User: steveboyslim; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    1,103
    Views
    156,498

    Any time you like. Steve

    Any time you like.

    Steve
  2. Replies
    1,103
    Views
    156,498

    I have only just seem your message, still...

    I have only just seem your message, still supplying parts, still building engines, still have the same phone number.
    I have replied to your message (three weeks late)
    The most reliable...
  3. Replies
    109
    Views
    51,737

    [QUOTE=prs;2310256]forgot to post this picture...

    [QUOTE=prs;2310256]forgot to post this picture off the new engine internals
    (1 set is for the nova ;))

    http://i66.tinypic.com/2ew1e8p.jpg



    Is the new engine a V8 ?

    Steve
  4. Replies
    275
    Views
    116,231

    The later block are cast from CGI material, the...

    The later block are cast from CGI material, the bores do not wear as badly as the XE/CLET block so wedging a later open deck or a closed deck XEV block would be the better option.

    Steve
  5. Replies
    5
    Views
    850

    Elring, Reinz, Gates or genuine, NO BGA or FAI...

    Elring, Reinz, Gates or genuine, NO BGA or FAI check if round or square tooth belt .
    Can supply what you need.

    Steve
  6. Replies
    109
    Views
    51,737

    Will do, I will give you a break down of what...

    Will do, I will give you a break down of what parts and labour goes into the head, but basically you will need the best part of £3k plus a head casting, ideally coscast.
    With the scavenge pipes...
  7. Replies
    91
    Views
    17,073

    I did not build it but I did supply many of the...

    I did not build it but I did supply many of the parts for the Autotech car, my friend assembled the cylinder head did most of the machining and engineering, Roper Developments ported the head, the...
  8. Replies
    109
    Views
    51,737

    Nice parts. Steve

    Nice parts.

    Steve
  9. Replies
    10
    Views
    7,084

    I can supply all the parts to build either a...

    I can supply all the parts to build either a short motor or complete bare engine.
    Specification will depend on budget and what power you want.
    XE block/engine can be converted, but if you are not...
  10. Replies
    91
    Views
    17,073

    Interested to see what power the engine makes, I...

    Interested to see what power the engine makes, I did not build it, but have just supplied many parts for a 1.8 engine which is being circuit raced.
    Made 220+bhp on Track 'n' Road's rollers.
    Dry...
  11. Replies
    93
    Views
    15,643

    Behind that plate is an adapter which takes a...

    Behind that plate is an adapter which takes a 14mm A/F (?) allen key, undo that and they should separate.
    Post a picture of it.

    Steve

    QUOTE=Benn;2283071]Hhmm i'd had mine in bits. Took out the...
  12. Replies
    93
    Views
    15,643

    They are all cast the same Like I said remove...

    They are all cast the same
    Like I said remove the threaded adapter and use the original CLET sandwich plate that the oil cooler pipes with the CLET adapter with a new 'o' ring, when using an oil...
  13. Replies
    93
    Views
    15,643

    Just unscrew the central threaded adapter (you...

    Just unscrew the central threaded adapter (you will probably damage it) and discard it, the thread in the oil pump housing is the same as the original oil pump so the original sandwich plate will...
  14. He also can supply these ...

    He also can supply these http://www.pngclub.com/forum/showthread.php?101314-Custom-Tie-Bar-and-Wishbone-setup&highlight=

    Steve
  15. Contact this chap, he can sort....

    Contact this chap, he can sort.
    http://www.pngclub.com/forum/member.php?8741-Jonlem

    Steve
  16. Have a look here...

    Have a look here http://www.pngclub.com/forum/showthread.php?110574-Small-block-nova-build/page28

    Steve

    Just realise you said 8v
  17. Replies
    41
    Views
    2,424

    Nothing to do with the shims. I have replied to...

    Nothing to do with the shims.
    I have replied to your PM.

    Steve
  18. Replies
    41
    Views
    2,424

    ?

    ?
  19. Replies
    41
    Views
    2,424

    ?

    ?
  20. Replies
    41
    Views
    2,424

    ?

    ?
  21. Replies
    41
    Views
    2,424

    ?

    ?
  22. Replies
    41
    Views
    2,424

    ?

    ?
  23. Replies
    41
    Views
    2,424

    ?

    ?
  24. Replies
    41
    Views
    2,424

    ?

    ?
  25. Replies
    2,102
    Views
    632,476

    ?

    ?
Results 1 to 25 of 63
Page 1 of 3 1 2 3