Certainly would mate. Would be interesting to see the standard factory LET IC. May have to make use of the extra space to the left of a 1.2 rad.
Printable View
Certainly would mate. Would be interesting to see the standard factory LET IC. May have to make use of the extra space to the left of a 1.2 rad.
Nice project mate cant believe ive missed this, looking forward to seeing the finished product :thumb:
Quote:
Originally Posted by Nova_Tek
They are tiny. So any things good. The std one could be fitted over one side of the rad, like most peeps do with the oil cooler.
Just been trying to find a pic of a LET IC, no luck but I have come across a site which sells them. They have it down as 240mm x 128mm x 64mm.
I just drew it on an A4 piece of papaer and it's about 2/3 of an A4 sheet if that. Deffo tiny like you said mate. That leaves plenty of room. Just need to go have a look at A/C rads now.
Quote:
Originally Posted by Nova_Tek
thanks gunny, i am too.
this condenser is from an agila/wagon r. found it over on ebay, its only 37cm wide so pretty small. I presume you will be having the pipes made up for it?
http://i193.photobucket.com/albums/z...88/7578_35.jpg
back to my project.
didnt do much today, test fitted my 7inch fan. does touch the IC bracket i made but isnt causing any harm. tried the bumper on again and it all still fits. phew. have got a 2nd to go on aswell.
http://i193.photobucket.com/albums/z...8/DSC02454.jpg
http://i193.photobucket.com/albums/z...8/DSC02455.jpg
onto the hoses from the turbo then, not 100percent happy with it but cant see how it can get any better. if im not happy when i put it back on when the engines built up again then ill consider sorting it out.
http://i193.photobucket.com/albums/z...8/DSC02456.jpg
Now that all my mocking up is done i stripped it all down and put all my bits away tidy.:)
http://i193.photobucket.com/albums/z...8/DSC02459.jpg
also took other small things off, such as the heater blower, wipers and linkage etc.
http://i193.photobucket.com/albums/z...8/DSC02463.jpg
re-fitted my rose jointed linkage. is a tad stiff as its been stood for a few months. only thing im worried about is that when you put it in gear from inside the car and take it back out, it wont centralise again. is it only the gearbox that makes it come back central?? will have to lube up my rose joints again.
http://i193.photobucket.com/albums/z...8/DSC02465.jpg
my one heater matrix outlet seems to come out right behind the inlet, is it ment to be like this? cant see how a hose would fit on with it like this.
http://i193.photobucket.com/albums/z...8/DSC02458.jpg
anywho, i got bored so thought id tidy my garages up. they got mega messy from neglect.
went from this
http://i193.photobucket.com/albums/z...2447Medium.jpg
to this
http://i193.photobucket.com/albums/z...8/DSC02462.jpg
thanks for looking.
bruce
That heater matrix pipe needs to be cut down mate ;) dont go too short though and try not to let it lose its shape.
Looking good keep it up :thumb:
This is correct, also see that lug on the inlet in the pic, well get the grinder on it mate, also worth fitting solid monts (maybe just rear one, if you want less vibration) as well.Quote:
Originally Posted by gunny
Straight bar looks loads better mate, getting there:thumb:
Scott
Just another thought, have you bent the clutch cable hole down and to the right to clear the inlet?
thanks guys, solid mounts would be good, just that with the set of three i wouldnt be able to use the gearbox one as thats the same as the o/s engine mount...Quote:
Originally Posted by gunny
i havnt bent the clutch cable hole yet, can i do it once the engines out or is it best when the engines in so i can see how far to bend it??
thanks for the info, helps if i miss anything.:thumb: