Quote:
Originally Posted by scott.parker
looked at that, and cant be arsed factor comes to mind, + id really like an IC just to be safe lol
Printable View
Quote:
Originally Posted by scott.parker
looked at that, and cant be arsed factor comes to mind, + id really like an IC just to be safe lol
had a 'play' with the belt lol
the bottom pulley is 3mm away from hitting the leg,
the belts about 1" from the fire wall, perfect really lol
http://i11.photobucket.com/albums/a1...cture079-1.jpg
Hammer time!
dont think ill need to tbh :thumb:Quote:
Originally Posted by scott.parker
and before you lot say, yes i have spun it to see which way it spins lol
pop up and have a look scott im only 30mins away lol
Nah cant be bothered, it's an hr drive! lol
30mins in the nova lol
lol £30-40 round trip!
Im hung like Saddam.
pardon lol
been busy lol
http://i11.photobucket.com/albums/a1.../Picture-3.jpg
for space, you could make a plenum that is turned thru 180 degrees, so the afm is facing the lhs, then the air pipework could come in & out over the gearbox
http://i11.photobucket.com/albums/a1...Picture080.jpg
http://i11.photobucket.com/albums/a1...Picture081.jpg
just what is all that brown stuff on my chair lol
Nick if you pull this off and get the car looking nice (none of the old baxter ways lol)
It will look and be really good.
hope you get this done it will be sh*t hot!!
problem is, if i bodge it works, if i do things properly it ****s up lol
heater motors going to be close lol
http://i11.photobucket.com/albums/a1...3/Image085.jpg
So the charger is mounted to the powerbox?
How heavy is it? That powerbox is only thin ally afterall ;)
well seeing as there only a pair of mole grips holding it on, not really that heavy, dont worry tho, its have metal plate on the inside of the box, and some rods over the top :)Quote:
Originally Posted by Adam
Cool
that bit of pipe work and the flange, weoghts more lol
im thinking of selling tho lol
update, all in, bttery moved, slight earth problem i think, that is all
http://i11.photobucket.com/albums/a1...3/Image005.jpg
http://i11.photobucket.com/albums/a1...Image006-2.jpg
http://i11.photobucket.com/albums/a1...Image007-1.jpg
upon starting im getting this now
http://i11.photobucket.com/albums/a1...Image008-1.jpg
i know ones the battery charge light, ones the eml (AFM unpluged) for the love of god i cant remember what the other one is, but i think its an earth fault and they keep going dim
heres a nice double pulley i made
http://i11.photobucket.com/albums/a1...Video000-2.jpg
cost so far
charger = £195
flanges = £40
extra pulleys = £10 (when i see novalicous to pay him lol)
and the bonnet still wont shut lol
cut a wheelie bin in half and have a big ass bulge lol
steal RJ's bonnet... that'll fit a house under there
wont work, as the chargers offset, so it would look gay lolQuote:
Originally Posted by mowgli
come on General, just get a biggun....
can't you cut the bonnet along the 2 styling lines & push the middle up till it misses????
How much is it catching? Bonnet lifters any good??
do they do 4-5" kits ? lolQuote:
Originally Posted by NOVABIKECARBED
lol that's rediculous lol big hammer then?Quote:
Originally Posted by General Baxter
and i put it as low as i could get it, i could of put it 1" higher tho lol
lolQuote:
Originally Posted by General Baxter
iv got a few bonnets, so out comes the grinder tommorow, raised bonnets are for gays lol
make it a biggun & then matt black it then?????
im thinking of just cutting a hole, putting some rubber capping around the sharp edge, and just leave it sticking out lol
well, at least it will help with cooling...
:d
half a wheelie bin ftw! lol