-
Nova sport
-
This is where I step in! Paul (the owner) got taken away from the projectdue to work and it never made it back onto the open highway. The car has been sat at his parents house since 2004, and has been off the road since feb 2003! Basicly he had the throttle bodies fitted and only had use of it for 1 day before it came off the road (in a way).
So 4 years of lack of true loving has resulted in it looking a little sorry for its self. The long term plan is to get it show worthy again. But for now we are planning on getting it back road legal again and running.
The engine spec was as follows (06/2002)
Velos Motorsport 1396 8 valve compression ratio 11:1
1.4 block
Block decked
Bored out
1.3 head
30 hours flow work
Enlarged ports
Stainless steel big valves
Inlet wasted stem
Exhaust standard stems for heat dissipation
Thin valve seats for improved flow
Cut down valve guides to improve flow
Head skimmed
1.3 crank (bottom end all balanced together as a set)
Balanced
Lightened
Shot peened for stress relief
1.3 conrods
Balanced
Lightened
Shot peened for stress relief
Ford Zetec fitment ARP bolts
1200 high compression pistons
Valve pockets enlarged for clearance
Thin anti-flutter piston rings with 3 thou clearance for minimum resistance (big, road clearance normally 1 thou)
Kent AST2 cam
Hydraulic followers
1300 flywheel standard weight for better take off
Balanced
1300 OEM clutch
Baffled sump
Aston engineering (Aston Martin) lower pulley with crank sensor phonic wheel original sensing wheel taken from Astra4 as used by Aston.
Ford crank sensor with mini timer plug
Lucas Throttle pot (type found on Montego)
Sagem wasted spark coil type without amplifier as fitted to Vectra
NGK 8mm silicone leads
NGK triple electrode spark plugs
Bespoke brackets for throttle pot wasted spark coil and crank speed sensor.
Distributor removed and replaced with bespoke blank made from cut down distributor
Irmscher inlet manifold with 2x Weber 40 DCOE 144 and 143 carbs
32mm chokes, 140 air collectors, F16 emulsion tubes, 130 main jets, 45F6 idle jets, 40 pump jets
ITG bespoke sock, which fits over all 4-air horns
4x bolt on 23mm 40 DCOE air horns
Facet solid state fuel pump, pre and post filtered
DTAFAST ECU and full engine management loom ready for throttle bodies (injectors, lambda sensor, and water and air temp sensors loom installed currently used for 3d map-able ignition. (Rpm/throttle position/advance)
ECU fed tacho
Shift light
Soft and Hard rev limiters
Launch Control (Soon to be fitted)
Full throttle shift (Soon to be fitted)
Last 3 minutes data logging
Brand new Vauxhall engine mounts
All ancillary components needed for engine intallation replace with new Vauxhall components
Gearbox
Fully rebuilt all new bearings and oil seals
F10 Housing
F13 gear cluster
F10 final drive (3.94:1)
RT Quaife Automatic Torque Biasing Limited Slip Differential
Gearbox housing polished
Samco Yellow Hoses
Exhaust
Stainless steel Powerflow exhaust with red tailbox, made to look original
Janspeed 4-1 tubular manifold
Output limited by exhaust at 98 bhp at the wheels at 6250 rpm around 130 at fly
Since this spec list it has had the throttle bodies fitted (half mapped to 4000rpm and produced 98 bhp @4000 rpm at the wheels on Velos's rollers, it has only been mapped to 4000rpm but should pull more when fully done after 4000 rpm it uses a Velos race x14xe map (175bhp!) as a base)
Should be some fun when running again (watch this space tomorrow!), wonder why I fancy a go in it?? lol
With a littl help from Count vauxalot (cheers James) we arranged to have the car transported from London to Newcastle to begin its work needed to get it back on the road.
Here is how I found it on saturday nigth when I got in from work (I seem to go to work on saturdays and cars appear on my drive during the day?!? 2 sports and a grey SX so far?)
http://img.photobucket.com/albums/v1...t/P1020863.jpg
http://img.photobucket.com/albums/v1...t/P1020868.jpg
Looking a bit green
http://img.photobucket.com/albums/v1...t/P1020866.jpg
http://img.photobucket.com/albums/v1...t/P1020865.jpg
http://img.photobucket.com/albums/v1...t/P1020867.jpg
http://img.photobucket.com/albums/v1...t/P1020869.jpg
http://img.photobucket.com/albums/v1...t/P1020870.jpg
http://img.photobucket.com/albums/v1...t/P1020873.jpg
http://img.photobucket.com/albums/v1...t/P1020871.jpg
http://img.photobucket.com/albums/v1...t/P1020874.jpg
http://img.photobucket.com/albums/v1...t/P1020875.jpg
All the panels are like new still
http://img.photobucket.com/albums/v1...t/P1020876.jpg
where it all happens
http://img.photobucket.com/albums/v1...t/P1020877.jpg
-
-
-
-
-
That was all last year will update it all later
-
Christ that's really the whole front off... Looks like a minty car tho, sure with your skills you'll get it up to spec in no time...
-
No time? That was sept 2008!!
-
Then stop funking about and get it finished.
