View Full Version : Few bits...
Too clear up my wanted list i thought i would put them all in one place as i now i know what i need.
URGENT: Front panel
Rear panel
Drivers arch repair panel
SR/GTE Front bumper/beam clips.
Standard nova 5speed Gear stick and rod (complete assembly) And complete linkage if possible.
I'l add anything else later.
Prices need to be plus postage and i also need postage cost.
Pm me or reply here.
blackmagicsr
17-06-08, 04:10 PM
i have dizzy if still needed pm me
Edited and added parts.
BUMP!
ive got the choke blank mate what are the pipes like where are they??
ive got the choke blank mate what are the pipes like where are they??
They are directly on the heater matrix and connect to the T pieces that are for the auto choke :p If you dont understand my rubbish description, I cant get a pic lol
you can or cant get a pic?
Cant, didnt get a pic of the car i took the carb off.
BUMP! Need GTE/GSI master cylinder and servo ASAP!
ainsley_brader
22-06-08, 12:01 PM
Have a servo and master cylinder here £20 delivered
Have a servo and master cylinder here £20 delivered
I presume its from a gte or gsi? If so Pm me.
ainsley_brader
22-06-08, 03:33 PM
Its on a gsi, i assume its original. Do you have dimensions for me to check
chappers1.3
25-06-08, 02:04 PM
got lots of pipes fella, sure the 1s i had on mine were for the autochoke.. or atleast 1 of them was..... thats if you still need them?
got lots of pipes fella, sure the 1s i had on mine were for the autochoke.. or atleast 1 of them was..... thats if you still need them?
I still need them But Might not have the money in paypal now lol
If you could find out, mainly need the one that is towards the drivers side.
Cheers
chappers1.3
25-06-08, 04:47 PM
i'll see what i got. jsut so i aint missin somethin, its the pipe that goes to the heater matrix, that has a T in it to go to the autochoke carb bit right?
i'll see what i got. jsut so i aint missin somethin, its the pipe that goes to the heater matrix, that has a T in it to go to the autochoke carb bit right?
I only want the bit that goes To the T-piece direct to the copper (or brass) pipes that come out the bulk head.
chappers1.3
30-06-08, 11:23 AM
no idea dude which pipe it is, all pipes are in a big bag, i will have that 1 i am sure, but can you tell me what length you need? approxiamately.
i'll send you a few of them that are about that size and you can use what you need. its that ok??
no idea dude which pipe it is, all pipes are in a big bag, i will have that 1 i am sure, but can you tell me what length you need? approxiamately.
i'll send you a few of them that are about that size and you can use what you need. its that ok??
No need now mate, made some fit :) Thanks anyways.
chappers1.3
30-06-08, 12:56 PM
ok mate no worries.
Bump I could really do with some arch repair panels now.
BTTT Looking for those bumper/beam clips.
Bump I could really do with some arch repair panels now.
theyre not a lot new somewhere around a tenner id guess i gave £9 each for mine from a motor factors
what panels are you after, have a new front panel, possibly a new front crossmember, vgc pass mk2 wing, bonnet etc.
Mainly rear arches, but maybe intersted in the x-member.
Bump for today before i go ringing around everywhere.
Welsh Dan
12-08-08, 08:48 PM
Do you still need a gear linkage? I've got the bit that sits on the gearbox mount.
I've emailed you with pic - complete gearstick - £20.00 - postage don't know yet - looking into it will get back
Thanks but i dont have the cash to spend on it atm. That project is on hold, hence why i havnt bumped this.
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.