View Full Version : picture request
novarobbo
05-11-07, 02:48 AM
i want to see some pictures of nova's on cav/cally turbo wheels as im seriously thinking about this atm :)
get posting your pics :thumb:
craig green
05-11-07, 10:03 AM
Only one I can think of is Chris Suttons silk violet GSi which now has Irmscher Softstars.
You realise these are 5 stud wheels and require a fair bit of adaptation & parts from other cars in order to fit?
peester
05-11-07, 10:52 AM
some one must have jamies's old white Turbo..?
http://i8.photobucket.com/albums/a50/novaco/P4240004.jpg
some one must have jamies's old white Turbo..?
TA DARR...
http://img.photobucket.com/albums/v13/riggy4/picture1119lz.jpg
http://img.photobucket.com/albums/v13/riggy4/picture1137yh.jpg
craig green
05-11-07, 01:13 PM
They dont really suit the car well enough IMO or justify the hassle of 5-studding the car simply to get them on.
Each to their own though however.
Hmm, I think they look quite good on a Nova!
Much work to fit?
I dont like them on a nova, they look sweet on a corsa tho.
Saloony
05-11-07, 01:42 PM
Hmm, I think they look quite good on a Nova!
Much work to fit?
Five stud conversion job. Rear disc coversion on the rear.
craig green
05-11-07, 01:44 PM
Hmm, I think they look quite good on a Nova!
Much work to fit?
Cav V6 rear hubs & brakes setup incl the 5 stud discs,
Front; requires a big block conversion & machined hubs to accept 5 stud hub flanges, 5 stud discs etc.
So all in, to perform the swap you need.
5 stud wheels x4 5 stud discs x4, big block conversion, 5 stud hub flanges, tyres, brake calipers & wheel bearings to suit.
peester
05-11-07, 01:52 PM
16" too so maybe bit toooight in arches..
little chance of them bein the new 'cesaro' then..
craig green
05-11-07, 01:59 PM
The offset isnt et49 on those Cav/Calibra rims... et42 perhaps?
novarobbo
05-11-07, 07:16 PM
Only one I can think of is Chris Suttons silk violet GSi which now has Irmscher Softstars.
You realise these are 5 stud wheels and require a fair bit of adaptation & parts from other cars in order to fit?
i know whats needed to fit them, and it is'nt the look i want.. its to be different and ive just bought some proper conversion shafts as my driveshafts were bodged when i got my car so i thought instead of going and getting 4 stud hubs machined for big block outer cv's i may aswell go for 5 stud (being different) then while im doing the back i'd have to go rear disc which was on the cards anyway
got a big block engine/gearbox..
got proper conversion shafts what use big block inner and outer cv's..
got/can get easy enough wheels/brake set up! can also use vectra rear set up! and most the vectra sri/v6 front brake set up's are 308mm so ive been told..
would need front hubs off chris astley? allready machined..
rear disc conversion mounts for the rear beam
for brake pipes i have a mate who can make braided gear..
then its all setting up after ive sussed the correct handbrake cable set up..
i know everything wont be ticked off on the list but i have a fair idea on how to go about doing it.. i hope!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.