beavy69
09-10-07, 12:29 PM
Ok so ive finally got hold of one of these together with some mismatched instructions and after two days of fooking about I have narrowed down the problems to these two:
1) Where to connect the following hoses on the manifold/throttle body:
- FPR vacuum hose?
- Dizzy vacuum?
- Crank case breather hose?
As can be seen below there are two blanks.....
http://i34.photobucket.com/albums/d149/beavy69/brighterandbetter.jpg
The other two arranged in an L shape, appear to simply form a tunnel around the side of the TB, as blowing through them is only obstructed by my thumb at the other end.
The instructions make reference to a suction pipe. Could that be one like this here on my GTE inlet, whereby the water flow creates suction:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1440.jpg
So would I be right in thinking that I can take this off the GTE and connect the suction part to the bottom of the L shaped tunnel/pipe, attaching the FPR vacuum to the other end?
If so would the breather go on blank 1 and dizzy vacuum on blank 2?
2) Wiring loom ....
Heres what I have got that I know the locations for:
http://i34.photobucket.com/albums/d149/beavy69/loom.jpg
According to the insturctions i also need:
- one to the petrol pump
- one to the cranking motor (terminal 50 - I have found this on the car)
- one to the ignition coil (terminal 1 - I think found it)
- and one to fuse box (terminal 15 - I have found this on the car)
Assuming therefore that they must be among the following that I have not been able to identify on the loom:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1438.jpg
This one above im thinking could be the fuel pump??
Although I cant find a plug like this in the engine bay:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1433.jpg
And there were also these two sets of two white wires taped away in the loom near the injector plugs:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1437.jpg
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1436.jpg
any ideas or does anyone know??
Lastly according to the instuctions I need a longer alternator belt which I obviously dont have yet, does anyone know which car I can get one from? Im thinking it will need to be just a couple of inches longer?
Thanks in advance for anyone that bothered to read all that it would be great if anyone can help.:thumb:
1) Where to connect the following hoses on the manifold/throttle body:
- FPR vacuum hose?
- Dizzy vacuum?
- Crank case breather hose?
As can be seen below there are two blanks.....
http://i34.photobucket.com/albums/d149/beavy69/brighterandbetter.jpg
The other two arranged in an L shape, appear to simply form a tunnel around the side of the TB, as blowing through them is only obstructed by my thumb at the other end.
The instructions make reference to a suction pipe. Could that be one like this here on my GTE inlet, whereby the water flow creates suction:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1440.jpg
So would I be right in thinking that I can take this off the GTE and connect the suction part to the bottom of the L shaped tunnel/pipe, attaching the FPR vacuum to the other end?
If so would the breather go on blank 1 and dizzy vacuum on blank 2?
2) Wiring loom ....
Heres what I have got that I know the locations for:
http://i34.photobucket.com/albums/d149/beavy69/loom.jpg
According to the insturctions i also need:
- one to the petrol pump
- one to the cranking motor (terminal 50 - I have found this on the car)
- one to the ignition coil (terminal 1 - I think found it)
- and one to fuse box (terminal 15 - I have found this on the car)
Assuming therefore that they must be among the following that I have not been able to identify on the loom:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1438.jpg
This one above im thinking could be the fuel pump??
Although I cant find a plug like this in the engine bay:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1433.jpg
And there were also these two sets of two white wires taped away in the loom near the injector plugs:
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1437.jpg
http://i34.photobucket.com/albums/d149/beavy69/08-10-07_1436.jpg
any ideas or does anyone know??
Lastly according to the instuctions I need a longer alternator belt which I obviously dont have yet, does anyone know which car I can get one from? Im thinking it will need to be just a couple of inches longer?
Thanks in advance for anyone that bothered to read all that it would be great if anyone can help.:thumb: