View Full Version : WIP- Past to Present
Pages :
[
1]
2
3
4
5
6
7
8
9
10
11
12
Thought it was time i got mine banged up in the Projects section as i doubt it will ever be 100% finished,Lol.
Anyways.
Bought the car in June 2005, back then it was std apart from Koni suspension, delocked doors, smoothed wings, and the SR steelies.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/1.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/2.jpg
Got busy cleaning her and back to blacking the bumpers:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/3.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/4.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/5.jpg
Also shoved the obligatory K&N on:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/6.jpg
Then i remembered that i had a set of 16" Masitaly rims lying about in my shed(off my old mk3 astra), they looked quite well-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/7.jpg
But being 7J width and a low offset they stuck out from the front arches, and wouldn't fit the rear at all, not without mods, and i didn't want to do that:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/8.jpg
So that was that idea gone.
July 05-I soon got tired of having to polish the bumpers about every week to keep them black so decided spray them matt black, also did the boot grab handle, came out quite well
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/9.jpg
Aug 05-Having recently sold the masitaly wheels by this point i put that cash towards a nice set of well fitting 15s, when i spotted a set of Vauxhall Cav cesaro wheels(best vaux wheels imo) for sale on Mig, so i snapped them on, and got them fitted:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/11-Cesaros.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/12.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/13.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/14.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/16.jpg
With it getting more towards Winter i bought a full set of GM mudflaps to prevent stone chips etc, look quite well
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/18-flaps.jpg
The car then stayed like this for about 2months,Lol, till i spotted a nice ashley exhaust system on the bay, and a cheap 4-1 manifold.
They soon arrived and were painted up, the 4-1 was then fitted with a heated lambda sensor:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/19-4branch.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/20-Ashley.jpg
But being for a mk1 bumper, the backbox hangs slightly too low for a mk2, oh well
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/21-Ashleyfitted-.jpg
Jan 06-
By now the front brakes were quite worn and needed replacing, so i took this oppourtunity to get some 2L 16v stuff.
The calipers were cleaned and hammerited Silver:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/22-2Lbrakes.jpg
And then fitted right on, much better :D
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/23-Brakesfitted.jpg
Whilst the weather was quite cold(Feb 06) i picked up a gsi rear spoiler, off Will on here iirc. That was sanded down, primed and sprayed with cans, and then G3'd, the finish was quite good for rattle cans:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/24-Gsispoilersprayed.jpg
Using Nicks guide i then had the job of drilling 8 holes in my boot lid, turned out to be easier that i first thought, once i found metal drill bit to use and not a wood one,Lmao.
So that went on:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/25-Gsispoilerfitted.jpg
March 06-A trip to the scrappy saw a set of rear headrests fitted:
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/25-Mar06-Rearheadrests.jpg
I also bought a set of gsi 6dial clocks and Sri clocks, to make a gsi/sri hybrid(white dials, but oil/batt guages too) Like so
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/26-SriGsiclocks.jpg
March 06-Saw a front OMP brace for sale right here on Novaload, so snapped that up and fitted it, needed a few mods to miss a few engine sensors(with it being for a SR model, but went on fine)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/27-Strutbrace.jpg
April 06-By now i was getting a bit bored with matt black, so a gsi front bumper was found, i couldn't decide whether keep it white, but i finally decided on Grey, looks better imo:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/28-Gsifront.jpg
Rear bumper was removed, and sprayed with filler primer to fill the "blobs"
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/29-Primedrear.jpg
After many nights of spraying and laquering, they were finally ready
Grab handle got the spraying grey treatment too.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/30-Rearfitted.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/31-Frontfitted.jpg
So went for a mini photoshoot,Lol
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/35.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/34.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/33-FenC.jpg
Got home, and asked for a few opinions and decided it was lacking something, thats it! Grey door handles to break up the white, sorted.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/37.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/36.jpg
Fuel cap was also replaced with a black one after i snapped the key in the old one,Lol.
This month also saw me sell my Fearless rear chrome brace, which i now regret.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/49-Rearstrut.jpg
May 06-Fancied fitting a single wiper, and luckily saw one for sale on here, off Tiiiiiimmy i think it was.
After spending quite a bit setting the linkage, it was on:
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/38-Singlewiper-May06.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/39.jpg
By now i got slightly bored of analogue dash dials, so decided find a digidash, thought i'd got a bargain but it turned out the main halogen bulbs had blown, so that was a tenner i hadn't accounted for. Was worth it tho:
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/40-Digidash-June06.jpg
June 06-Planned on fitting a set of clear rear clusters, and found a set on ebay, but the top lense was cracked, but i bought them anyway.
Test fit, didn't really like them personally
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/41-Clearrear.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/42.jpg
So instead i got another set of std GM rear lights from Andy Bishop, and after many hours of cutting, heat gunning, tigersealing, cleaning, these babies were born :D
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/43-Customrears.jpg
And soon fitted
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/44-Customsfitted.jpg
Much better than clears.
July 06-By now i'd had 1.2i power for over a year, the gearbox had started to whine( i later found out why,Lol)
So a quick trip along the A50 to fetch a F15CR gearbox that I spotted on Corsasport, a bargain at ?15
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/45-F15-July06.jpg
The original plan was to fit the box to the 1.2i, but i thought Meh, swap the whole engine, the same night i spotted a 1.4sr engine for sale, no g/box, but with my newly aquired f15, that didn't matter
So the engine was bought from John(g88 kag on here, chees mate)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/46-1400engine-August06.jpg
I then decided to run it on SPI, not carb, so off came the Weber 32/34DTML, and that got sold on http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/47-Weberdtml.jpg
As did the 4-1 manifold that came on the engine(i already had one)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/48-4bran.jpg
So that saw me with almost my money back on what the engine cost,Lol.
Aug 06-Engine conversion started, my first ever,Lol.
Old 1200 coming out
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/55.jpg
Car looking sorry for itself with an empty bay ready for cleaning up
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/56-Allgone.jpg
Got the F15 bolted up to the new 1400 engine
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/57-Neweng.jpg
and got that plonked in
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/58-In.jpg
Not really wanting swap the engine to gain about 5bhp on my old 1200, i fitted a few "tweaks" to the 1.4 engine.
A c14se cylinder head was found at a local scrappy, and painted up
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/51-Newheadrocker.jpg
A 1.3Sr carb inlet then had the ports modded to match the head:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/52-Modded1300inlet.jpg
So the original 1400 head was removed, and the head gasket changed, then the new head fitted:
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/59-ChangeHg.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/60-Newhead.jpg
At this point i noticed my old F10 g/box from the 1200 had hardly any oil in it, hence the whining,Lol. And the waterpump had nearly seized solid. Luckily it held out until the new engine got fitted.
A quick strip down of the 1200 engine, a few of the coolant/oil passages looked blocked
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/65-Dismantleoldengine.jpg
So it was given to the local scrap man,Lol.
Sept 06-Fitted a universal K&N type filter, as the old one was damaged:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/66-NewKN-Oct06.jpg
Dont really like the look of it, but it does the job,Lol.
With the inlet slightly leaking air(think maybe cracked somewhere) I picked up a rare mk1 astra 1300s inlet off ebay(which has longer runs and a much better inlet hole)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/67-Dec06.jpg
It was then modded and sprayed satin black, and fitted with a new 1.8SPI throttle body.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/69.jpg
Oct 06-The car went to a Rolling road day at Mikeanics in Congleton, where it made 84bhp, not bad, up from 59bhp as std.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/667-Oct-RR.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/6678-RRwheel.jpg
Dec 06-By now i wanted more power, and just as it happens i spotted a Kent AST2 cam for sale, so i had it;
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/71-AST2cam.jpg
Also got a C14se rocker cover, looks nice and curvy,Lol.
Sanded that down, primed it, and its now Satin black:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/68-1.jpg
Kept the cam for a bit until i found some t40 carbs to use with it, i wasn't having much luck tho, so i bought some other bits
A set of half smoked rears, which look cool, but are fooked as one of the mounting posts is broken off, : (
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/70-Halfsmoked.jpg
So they just sit on my desk,Lol.
Jan 07-Having survived another winter, my cesaro's were looking a bit tired, but having no other wheels to fit whilst refurbing them i bought another set, cheers to John again.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/72-Newcesaros.jpg
They are currently mid refurb and need finishing.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/73.jpg
I was recently considering selling the kent cam, but luckily i found a set of Twin 40 weber dcoe's, that looked tired, but in working condition, they soon arrived:
Not looking too well
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/75.jpg
But a wire brush and splash of petrol works wonders
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/76-T40scleaned.jpg
Much better.
They are currently waiting to be fitted, but i have a slightly problem with a cathedral inlet(my head ports are round) so the inlet needs changing/modding:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/77-T40inlet.jpg
And that pretty much brings you up to date, got a few things planned.
Both bumpers need respraying, and i want the rear grab handle completely smoothing.
The carbs need fitting as does the cam and satin rocker cover.
I also have a runabout car, so the rear will now be stripped on the nova, floor sprayed etc.
And the cesaro's need finishing, dont know whether decide hurricane grey(same as bumpers) or White tho, few photoshops:-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/Cesaro1-chop-Black.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/Cesaro-chop3-White.jpg
Thanks for reading
hurricane grey for the wheels fella
you saw how good mine looked on them ;)
Im 90% going for hurricane grey.
I need sleep first tho lol
get to bed then you slag :lol:
enjoyed readin this buddy
love the cesaro'sgo grey tho ;)
c'2.0lrt
31-01-07, 08:06 AM
nice post mate,grey wheels,nice work
Matt2107
31-01-07, 10:22 AM
Excellent post there mate.
BigStan
31-01-07, 10:22 AM
Fooking good thread keep it up mate !
Cheers
Been today to see about getting the t40 inlet modded, but no can do :(
He can only remove metal, not add it.
So thats pi**ed me off a bit,Lol.
If i dont find a round port inlet soon the carbs/inlet and AST2 etc will be sold on,and over this summer i'll fit a X20XEV engine(yes 2L ecotec,Lol)
Will put up a few updates when i finish the wheels etc.
Rick Draper
31-01-07, 01:34 PM
Looking very nice. I regret selling it.
looking ace ad
will the ast2 fit the gsi lump , if it does sell it me lol :thumb:
ANDYRACER
31-01-07, 05:15 PM
Cheers
Been today to see about getting the t40 inlet modded, but no can do :(
He can only remove metal, not add it.
So thats pi**ed me off a bit,Lol.
If i dont find a round port inlet soon the carbs/inlet and AST2 etc will be sold on,and over this summer i'll fit a X20XEV engine(yes 2L ecotec,Lol)
Will put up a few updates when i finish the wheels etc.
Dont you dare, t40s are cool. :cool:
looking ace ad
will the ast2 fit the gsi lump , if it does sell it me lol :thumb: Indeed it will, it might make your Afm have a bit of a fit tho lol
Dont you dare, t40s are cool. Yup, but i dont want fit them with the wrong inlet, fitting the right inlet will give "free" power.
I've managed to get almost everything i need to fit the 40s now, and all been done on a budget, just the inlet might push the budget a bit, if i have to resort to buying one new.
Im dont have much to do tomorrow, so for a bit of a laugh im slapping the ast2 in, see how the spi reacts to that,Lol.
Cheers for comments.
looks ace dude as i've said before,
had it been painted down the sides?
looks so white and shiney,
is a beasty!
lovely looking, shame you dont know nothing about the mechanical side of things lol :p
looks great ad :thumb: iff you do sell the t40s and inlet give me a bell...
Really enjoyed reading that, and feck me thats a clean shell too! Loved the lense modding also! Top work.
looks ace dude as i've said before,
had it been painted down the sides?
looks so white and shiney,
is a beasty!
The arches were repaired after i got it, and arch/lip resprayed.
Apart from that paintwork is original, but the doors/front wings were new a few years back so the paint on those isn't too old.
2 Winters have taken their toll tho, and ideally both rear arches now need the lip replacing to make it 100% gd. And a few stone chips here and there, all in all, not done too bad for a 15yr old car.
Lol @ draper.
I'll let you know mike if the 40s go for sale
Cheers BT :)
ah,did wonder looks better than std paint,
very very nice dude,
James P
31-01-07, 09:22 PM
nice car mate.
like the rear smoked lenses alot good idea.
car needs to be lower tho
From June 06 onwards the rear springs were swapped with what i thought were 60mm springs, but the turned out be 40mm.
So the rear is sitting a bit high atm.
That may soon be sorted tho :D
Wee update- Seeing as it was warm as fook today i got some work done.
Got 3 of the new cesaro's primed, not done the fourth yet as its in slightly worse condition and needs more prepping get it completely smooth
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/78.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/79.jpg
Also got the sri rocker cover sprayed up Satin black, and did the oil cap aluminium
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/80.jpg
And got the 14nv coil sprayed up
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/81.jpg
Wheels are going hurricane grey, eventually,Lol
nuds sr
04-02-07, 01:10 AM
when you get your set of cesaro's painted and back on your car would you be interested in selling the other set of them that you have ? if so pm me or email me at nuddis_5dog@hotmail.com to let me know because i have looked everywhere for a set and cant find any cheers alan (nuds sr)
Sorry mate, because of how rare they are, im keeping the other set for spares, yeah i know im greedy,Lol.
get redbull can on ignition coil will look mint lol
i was guna post bout 2nd set of cesaros too but you allready answered :(
nuds sr
04-02-07, 09:32 AM
come on dont be greedy im willing to pay decent money for them if thats any sort of persuasion
I'll think about it.
xxx nova xxx wanted to buy one off me ages ago,Lol.
Excellent thread and car ad! The simple mods make it stand out imo. Budget novaing at its best!
(Add another vote for black wheels for me too)
copycat, spraying wheels same colour as mine :P
only joking ad, told you to do it from the start, will look **** hot :thumb:
copycat, spraying wheels same colour as mine :P
You copied the colour from my bumpers first :p lol
Off out in a min finish priming the other wheels.
good thread mate! does look good! will be good to see the 40's on etc
coochiSR
04-02-07, 08:32 PM
This is a quality car and thread!! Its quiet suprising how many bits can be "swapped" between Vauxhall's cos i'd of never of thought about a C14SE head and a 1300 carb inlet, its just amazing what can be learnt! I know now who to go to when i need some technical tips :D. And i agree go for the hurricane grey wheels, looks spot on! Keep up the good work Ad!
Dan
Cheers for comments.
Wheels shall be finished this week.
And i'll decide what do with the carbs,Lol.
Rick Draper
04-02-07, 08:56 PM
Do you just use halfords spray on the wheels? Got a set coming that i need to do.
Also do you laquer them?
Sr_nova_gameover
04-02-07, 09:03 PM
that has inspired me!!! amazing
did ur (1.2i was it) have a five speed box???
Paul
Yeah Rick.
Normal spray paint from halfords/motor factors.
If you do a colour like gloss black/grey you dont need laquer as its not met.
But i always laquer things like bumpers/wheels to help with stone chips.
So i will be laquering them when there finished.
Just hope tyre fitter dont wreck them,Lol.
Heres a guide from mig/mk3oc:-
http://www.novaload.net/forum/showthread.php?p=617875#post617875
that has inspired me!!! amazing
did ur (1.2i was it) have a five speed box???
Paul
Nah the 1.2i was a 4spd box.
Served me well, even lacking oil,Lol.
Sr_nova_gameover
04-02-07, 10:00 PM
Nah the 1.2i was a 4spd box.
Served me well, even lacking oil,Lol.
would a 1.3sr box work???
Sr_nova_gameover
04-02-07, 10:02 PM
was the rev clock standard 2???
Paul
Ye a 1.3sr box would work.
I made the gsi/sri rev counter clocks.
Std was just a speedo/fuel/coolant guage.
Sr_nova_gameover
05-02-07, 11:43 PM
cool coz i would love to find a 1.3sr but its really hard so i was thinkin of a 1.2 and put a 1.4 head on it and high lift cams which pretty much makes it a 1.3 but not if u no wot i mean. and then the box would fit lovely....
how easy was it makin the clocks??? or was it that u just buy them and fit all the sensors?? coz isnt the rev sensor on the gear box on nova's??
this car u have made looks the tits and i would like the one i want like urs but in my own little way..
cheers for helpin
Paul
Clocks just undo, and re-fit the white speed/rev.
All novas have the same fuel/coolant etc sensors? so they work fine.
very nice indeed, needs a 2.0 ecotec tho;) (read: i want the AST2 cam lol)
no, very clean - like it alot for a white one :D
Ash
Cheers :)
Lol.
If the carb idea goes bad, it will be eco-tech'd
Either a 2L, or 1.6 16v with a manztel type inlet.
So 8v stuff will get sold.
oh yea, 1.6 ecotec - keeping it smallblock!
Whats the 8v tho? 1.4 or 1.6? it's and SE head anyway isn't it? i'll keep my eyes open, took me ages to find mine.
Ash
Its a 1400 8v, 14nv block, 14se head.
Took the carbs to bits today to make sure all the jets etc were clean.
They couldn't have been running too well previously as one of the accel pumps was completely blocked(just a small dribble of fuel coming out,Lol)
So i blasted that out with a bike tyre pump, and its all sorted now.
Nearly had a nasty accident tho, didn't realise how fooking far fuel shoots from the pump jet.
Any fuel in eye gen lol
Also have a Round Port T40 inlet on the way :) Big thanks to MikeySR who pointed it out on ebay to me, the auction wasn't titled very well, so it had one bid in about 6days.... :)
lol fuel in the eye hurts lol , should have an eye bath ideally
Luckily it missed my eyes and just went up the side of the shed lol
It was a close call,Lol.
ahh good to hear you won the inlet ad!! good stuff! lol good job you didnt get hit by the fuel tho pmsl lol
craig green
07-02-07, 12:50 PM
Awesome write up there.
I love this car, it looks so clean & unique. Major hats off to you for doing it on a budget as & when bits turn up.
In hindsight it must be so much more fun like that than just waving a chequebook at demon tweeks or whoever.
In hindsight it must be so much more fun like that than just waving a chequebook at demon tweeks or whoever.
Indeed it is, the only things i've ever bought new for the car are gaskets, and tyres lol
Cheers for the comment :)
craig green
07-02-07, 01:38 PM
Its possibly my fave car on here really.
looking at the pics I'd almost accept a swap with mine...... really is a nice evolution though. The simplest Novas always look the best. A lesson to the fibreglass brigade at how to attract the right attention IMO.
Got two the wheels sprayed up today, colour came out quite well.
Need do the other two this week. http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1110002Medium.jpg
Also planning on removing the rear interior tomorrow, with the rear carpet etc. Cleaning the sound deadening off the floor and spraying the floor up white. Plan on getting a pair of buckets/harnesses in the future sometime for the front. For now tho, std sr front seats.
Always loved your car ad, credit to you, drop me a line when you come to sell it :P
Always loved your car ad, credit to you
Cheers Si :)
when you come to sell it :P
It will never happen :D lol
Round port t40 inlet turned up today, in very good nick too.
I've smoothed the inside of the runners down with 60grit paper, let it nice and smooth, but rough enough so fuel flows through correctly.
Quick pic, compared to cathedral shape inlet-
I guess the round head larger valves make up for smaller port sizes.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1140001Medium.jpg
Turns out and may be selling all the t40 stuff tho and fitting a 16xe, not decided yet.
craig green
15-02-07, 12:43 PM
mmmm 16XE.
Is the cathedral type to fit a 16SE head type?
Cathedral fits 1200/1300 carb.
Round fits 14se and 16se.
Really tempted sell the lot and fit a 16xe tho, about same power as t40 1400, but good mpg all day long. And a lot of scope for future mods, bike tbs etc...
macc nova
15-02-07, 04:26 PM
Do you do all your painting with rattle cans? Also am i right in thinking they are the halfords cans or not? (just when i use cans it never comes out that good) lol
Yeah, all with rattle cans.
I've never visited a bodyshop in my life lol
I used Holts paint from a local motor factors, halfords are way too expensive(?5 for 300ml can), Holts are ?2.74 for 300ml, the factors owner puts them as Trade price for me tho :)
its easy enough to do as long as you apply it properly. love the wheels bud!
ANDYRACER
15-02-07, 05:30 PM
How much for the engine with the t40s matey?
Just been out to Maplins, to pick up a few switches, a 30A relay, and some wire to wire up my own fuel pump relay instead of cutting the spi loom to bits...
So hopefully i'll bolt the carbs on over the weekend, get the idle mix/speed sorted, and see what there like.
macc nova
15-02-07, 06:07 PM
cheers, how much do you get it at trade price as i use my mates account lol, good work btw lol
supernova1992
15-02-07, 06:36 PM
Personally, i'd say white. too many grey wheel/bumper combos out there nowadays. Cesaros look great in white too.
cheers, how much do you get it at trade price as i use my mates account lol, good work btw lol
Not sure how much they are normal public price, think there ?3 ish.
Supernova-I would of gone for white if the car wasn't white, white looks good on red,black,blue etc etc, but dont think it would suit white.
Sirnixalot
15-02-07, 07:26 PM
looking forward to pix on the carbs! hope it doesnt give you any **** :thumb:
good man ad, you'll love the sound of them!
ANDYRACER
15-02-07, 09:00 PM
Supernova-I would of gone for white if the car wasn't white, white looks good on red,black,blue etc etc, but dont think it would suit white.
Oi cheeky sod, white wheels look cool on white novas :thumb:
Lol, on some they do, i dont think cesaro's will on a white car tho.
Altho white does make them look much bigger. HMMmmm
Rah, dont know what to do,Lol.
slammed saloon
15-02-07, 10:12 PM
a mate of mine had a black sri with white cesaro's on, lowered 60mm and it looked VERY tasty, i then spent the next 6 months trying to persuade him to sell it me before he crashed it :cry:
slammed saloon
15-02-07, 10:21 PM
i personally dont have any mate but ill speak to him over the weekend and ask him for :thumb:
Hmmm
http://img.photobucket.com/albums/v86/Nova-crew/Cesaro-chop3-White-nobadges.jpg
Gloss white paint is megacheap to buy too,Lol.
Sirnixalot
16-02-07, 01:53 AM
looks like a rolling tub of vanilla ice cream with that much white lol
Lol, might just finish the other two in grey then.
Can't decide what to do now, both colours have there good and bad points.
Got the T40 alternator bracket welded up today, local Mini place did it me for ?3, made quite a nice job of it too.
So im ready to chuck the ast2 in, and the 40s on now.
Hopefully next week.
Carbs are ready to go on, bolted to inlet etc.
Word of advice to anyone with a round port inlet, it seems the cast that the manufacturers make them from isn't really a direct copy of GM heads/inlet.
So bolt the inlet up and you get a "step" as the runner meets the head, could cost a few bhp, and afterall its free power.
pic:
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1180001324234Medium.jpg
All four runners are the same.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P11800063242Medium.jpg
Got to wait for me dad get home give me a hand bolting the carbs on, i use m8 bolts instead of studs/nuts so have to hold the weight of the carbs,line inlet up, put bolt in etc, bit difficult with two hands. lol
Cheers Benn.
Carbs on are now, fook me what a battle to get those on. Lol
Got to sort fuel pump and ign coil etc tomorrow, and fingers crossed it might run lol
not using the std pump and that?
Spi pump, with a regulator.
Just hope the regulator can handle the spi pump's pressure.
Sirnixalot
20-02-07, 01:38 PM
any news?
Yep there is.
Its Alive and Running :D :cool:
Took a while because of a lot of unexpected problems, like the spi coil having 2 ign live wires, but one splices into the spi ign module(which is now unused), so i had no 12v at the Sr coil. That held me up for a bit,Lol.
Also got to run a new wire for rev counter, as spi one is ran through the ecu.
And the lowered alternator bracket jammed the alternator fan blades :wtf: Good job i noticed that before trying to start engine, may have snapped the cambelt/alternator shaft. So i had to get the grinder out(again) and grind down the edge of the bracket.
Now all is good, they fired up quite easily, and sound fookin insane compared to the spi system.
Got to hook up the throttle cables tomorrow, and set the idle mix/balance screw, then go for a drive :cool:
Few pics(t'd the return line in, and have the spi pump running from a switched 30A relay, seems to work fine, altho im a bit confused about whether i should turn pump on then try start the engine. Or start the engine(it should fire up from the fuel in the carb bowl, then switch the pump straight on. As with pump on and engine not running where will the fuel go thats being pumped through the line? Down the return?):-
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/Image1.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1200002Medium.jpg
Also got my Satin black rocker cover to fit.
Sirnixalot
20-02-07, 08:04 PM
looks great!
do you not need to use the vacuum advance on the dizzy anymore?
Nope.
And besides which my carbs dont have the vacuum advance connections on them, there quite old skool.
All done now, throttle cable arrived from FastRoad Cars today, top guys there. The 1m cable is plenty long enough.
Took a bit of getting used to with the throttle pedal as its opening 4barrels compared to 1 originally, alls good tho, easy to get the hang of after a few miles of driving.
Going to booking it in for a RR setup soon.
Also fitted my satin black sri rocker cover.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1234533430002Medium.jpg
Still got the Cesaro wheels to do, as im now spraying them gloss white with smoothed centre caps.
macc nova
23-02-07, 08:42 PM
lovin it mate, really want some t40's on mine but after the problems i had with the 32/34 im unsure lol, the satin black rocker cover is a nice touch
Cesaro's are now white,Lol.
Still got centre caps to smooth and spray.
Chose white because its different, white car/black rims has been done to death, and white makes the wheels look larger :)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P204000145645Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P20400045465Medium.jpg
Before PV got both bumpers to respray, and lower rear springs to fit.
May fit GSi skirts sprayed hurricane grey too... Not sure yet.
:thumb::thumb: up, looking good, glad to see you've gone with white wheels and not blended in with the crowd. If i was to do another nova, it would look like this ;)
How hard/easy was it to set the carbs up then? to get it drivable i mean?
Ash
Piece of piss on the carbs, i got lucky and happened to find a set with almost perfect jetting for my engine.
Just set the idle mix by watching the rev counter, set the balance by ear,Lol.
And all is good, idle is quite steady, and it pulls well.
Tiny flat spot just before you go onto the main jet(about 3k rpm), but you can hide that with the accel pump jet.
I get no spitting back through the carbs, no exhaust popping etc, so they must be set up quite well.
Ideally it needs setting up(running a touch rich in i think the prog/idle circuits), but i'd quite easily say i could live with how it drives atm, even drives well at low speeds(pulls in 5th from low revs)
5 throttle pumps to start first thing/in cold weather seems to do the trick on mine, fires up first time, and idle's on its own within a few hundred yards.
Just need replace the camshaft oil seal, i must have nicked it when i was sliding the cam in and its leaking down the back of the cambelt cover slightly. So will get that changed asap.
O, and i need a new top seal for one carb too, its slightly damp with fuel.
But i'd have to buy a complete service kit for just one gasket, so might do that soon and fit new gaskets all round.
ad they look soo nice white! um might buy a set lol
thought about doing mine white, but cant be ****d with keeping them clean :lol:
Lol, cheers for comments.
Yeah Ste they may be a bit difficult keep clean, apparent spraying that RainX stuff for windscreens onto the rims helps the dirt not stick.
We'll see,Lol.
think i'll stick to being a sheep and get softstars :roll:
yeh get soft stars ste! as said when i spoke to you i'll have yours!
yeh my white cav slabs are a c**t to keep clean! i laquerd them loads etc now its like stains are stuck on them lol so im going to try and wet and sry them to see if it gets them out lol
was waiting for that reply saying you'll have them.. lewis lol
lol i knew you knew it was coming lol
anyway, back on topic..
pic's of white cesaor's fitted please :D
yeh when they being fitted? cant wait to see it!
Oooo, maybe a while yet,Lol.
Waiting for the paint to fully harden.
And then i hope the tyre fitter doesn't wreck them :(
take all the shelves out the oven, and stick one in at a time, that'll soon harden them lol
Lol, i'll just leave them inside my shed for a week or two.
No rush anyway.
gary_126
11-03-07, 03:15 AM
Fantistic thread, just read the whole thing. Love the simple modds (dont alot of similar stuff to my nova, which u will have seen on migweb (GaryVaux - red c16xe nova sri)
Glad u fitted the twin carbs, the c16xe is becomming as common as the 20xe in novas now:(
Wil you be at pvs or billing?
kevster
11-03-07, 08:43 AM
take all the shelves out the oven, and stick one in at a time, that'll soon harden them lol
love it :thumb:
lee coley
11-03-07, 09:30 AM
put the wheels in the house next to the radiator it will harden the paint then when tyres are fitted use a bit of t-cut to bring them back up.
long live the nova nice job mate :thumb:
Fantistic thread, just read the whole thing. Love the simple modds (dont alot of similar stuff to my nova, which u will have seen on migweb (GaryVaux - red c16xe nova sri)
Glad u fitted the twin carbs, the c16xe is becomming as common as the 20xe in novas now:(
Wil you be at pvs or billing?
Ahh hi gary, yeah read through your project on Mig :thumb: Nice
Yep it will 100% be at PV, and probably Billing too.
Cheers for the comments everyone :)
Got some 60mm rear springs from SRS1 this week, so they will be going on soon :)
craig green
14-03-07, 06:00 PM
Hats off for the carbs fitted.
Wheels look cool too. You made the right decision!
very nice thread, very interesting, how did you solve the port mismatching on the inlet manifold in the end then? did you dowel it to the head? and also when you had the engine running on the 1.8spi throttle body were you still running the engine on the 1.2spi ecu? i'm just asking out of interest that's all, i'm well impressed with the 84bhp you got on that set up, was it economical?
Maccas
think i'll stick to being a sheep and get softstars :roll:
softstars do look wikid on corsa's though just like speedlines on nova's
http://img.photobucket.com/albums/v13/riggy4/04122006084.jpg
my old girly car lookedgood on them
oh and ad , hurry up with the wheels lol
looks ace :thumb:
Just hope tyre fitter dont wreck them,Lol.
"next time" have the tyres fitted but not blown up before you paint them ;) thats what we do at work anyway
very nice thread, very interesting, how did you solve the port mismatching on the inlet manifold in the end then? did you dowel it to the head? and also when you had the engine running on the 1.8spi throttle body were you still running the engine on the 1.2spi ecu? i'm just asking out of interest that's all, i'm well impressed with the 84bhp you got on that set up, was it economical?
Maccas If your referring to the inlet not quite lining up with the head with the 40s, i just opened the head port out slightly.
I had a 1.8 throttle body on both my old 1.2i engine, and the 1400 engine.
It was the 1400 engine that made 84 ish bhp. It drove great and was very economical, 35+MPG driving foot to floor everywhere, about 40mpg on the motorway, even with a CR box.
It had the std 1.4i ecu, and 1.4i injector. Seemed to fuel ok.
I was planning on fitting the AST2, a 1.6i injector, and getting a "chip" to raise the rev limit(as it made 84bhp on the limit, a higher limit could of seen 90+), but decided go for 40s instead.
Cheers for the comments :)
Burgo, i wish you had mentioned that before i started the refurb! Lol. Sounds like a top idea so you can get paper/masking tape under the lip of the tyres.
Right, carried on with the cesaros today.
Got the centre caps smoothed, took fooking ages, many skims of filler, hours of sanding etc,Lol.
But they came out quite well, not 100% perfect smooth, but ok for me, and the time it took.
Ive not seen a set completely smoothed before, so i hope its a first :p :)
As std they have a badge, under the badge is a 1/4" hole, and a 2inch recess where the badge sits.
Im hoping totally smooth will make the wheels look bigger than they actually are.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P2210003Medium.jpg
They look alright I suppose :p
coochiSR
24-03-07, 05:04 PM
Very nice Ad, sell me the other set!:p
Lol, theres wayyyy too many people asking the buy the otherset lol
coochiSR
24-03-07, 05:11 PM
So, i know you ain't selling them though :(
ANDYRACER
24-03-07, 05:16 PM
Im liking the smooth cnetre caps Ad :thumb:
Whats economy like on the carbs?
The other set may be for sale one day,Lol.
Andy-Not bad at all mate, saying they aint even set up properly, i get about 27mpg.
That includes some floored B-road action, no motorway driving.
I drove a mates XR2 which is on 40s the other week, that aint setup either, but it drives ****e compared to mine, loads of flat spots and idle all over the place(my idle is as good as it was on spi). So amazingly i seem to have got lucky and got a set of carbs almost perfectly setup for my engine.
I still wouldn't say no to a RR tweak tho, just to get a bit more low end power, but the money it may cost i'd probably rather put towards another engine tbh. Maybe a 1600 8v and bolt the carbs on that, or mpi with aftermarket ecu. Again, money i dont have atm tho :(
ANDYRACER
24-03-07, 05:28 PM
The other set may be for sale one day,Lol.
Andy-Not bad at all mate, saying they aint even set up properly, i get about 27mpg.
That includes some floored B-road action, no motorway driving.
I drove a mates XR2 which is on 40s the other week, that aint setup either, but it drives ****e compared to mine, loads of flat spots and idle all over the place(my idle is as good as it was on spi). So amazingly i seem to have got lucky and got a set of carbs almost perfectly setup for my engine.
I still wouldn't say no to a RR tweak tho, just to get a bit more low end power, but the money it may cost i'd probably rather put towards another engine tbh. Maybe a 1600 8v and bolt the carbs on that, or mpi with aftermarket ecu. Again, money i dont have atm tho :(
Want to sell the carb set-up? :p
coochiSR
24-03-07, 05:29 PM
Ad you still got that 1300 inlet?
chris-gsi
24-03-07, 05:44 PM
cooch have you got a starlet seen you on the starlet site? me birds dad is dave sells loads of starlet parts, is based around this way as well. his site is
Starletgtturbo.co.uk
coochiSR
24-03-07, 05:58 PM
Daveburwash and no my bro has, im on the site too though lol, Pm you later will ahve to meet up, your local to me!
Want to sell the carb set-up? :p
Hmm, maybe?
Coochi-I still have it somewhere yeah, cant remember where tho, maybe in the loft.
chris-gsi
24-03-07, 06:28 PM
Daveburwash and no my bro has, im on the site too though lol, Pm you later will ahve to meet up, your local to me!
yes mate im from braintree
coochiSR
24-03-07, 06:57 PM
Ad could you have a look for me please, in desperate need now lol
I'll have a look a bit later mate.
coochiSR
24-03-07, 07:00 PM
No worries, werent meaning right this second lol, PM when ya know a bit more please ;)
Lol
I'll have a look when back from pub(England are about to start, better get a shift on,Lol)
coochiSR
24-03-07, 07:17 PM
Quick Ad!! and no worries!
cooper_nova
25-03-07, 03:15 PM
those cesaro's look mint in white ad!!!
i was thinking about white cav slabs for mine lol
bieransri
28-03-07, 09:33 AM
what white did you use for the rims? same as car?
No mate.
I used Gloss white. Im hoping they look ok against the glacier white paint.
Quick update:
A 1.6 16v engine should be going in in next few weeks/months :) ;)
Basically will be needing the car for work soon(will be early starts, so need 100% realiability day in, day out) and better mpg.
All 8v stuff will be for sale: Carbs,inlet,ast2, 1.4sr dizzy, 1.4sr fuel pump, 14se head, 4branch manifold etc.
PM me if anyones interested.
coochiSR
30-03-07, 07:08 PM
Hope it all goes to plan, you have a PM ;)
Quick update.
Collected this on Sat, cheers sean.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/X16xeengine.jpg
Have waterpump,cambelt, etc to replace. And getting the block all cleaned and painted up
The 1400 engine has developed a weird misfire that seems to come and go, but im hoping it lasts ok till June time, when my insurance runs out, so i can fit the 1600 16v. It will be entirely std for the minute, apart from a set of kent cams.
your not messing about are you ad lol
bieransri
17-04-07, 07:00 PM
how come you chose the x16xe? and not the c16xe?
Because this x16xe came up for sale.
Not really much difference between the two.
Both have the same potential.
O, and x16xe is ?80 less insure ;)
bieransri
17-04-07, 07:10 PM
cool, got everything, transponder, chip key etc?
if so might aswell for less money overall, looking forward to seeing it go together as ive considered the c16 for mine
Aye mate got everything.
The wiring looks entirely straight foward too
The entire engine loom just undoes from the engine in about 20secs..
Just about 6/7 wires to the ecu to wire, and a few at the transponder pickup.
And ive got the SAI and EGR to block off, which a c16xe wouldn't have. But thats nothing an alloy sheet wont sort.
So if you want a 1600 16v i wouldn't particularly hold out for a c16xe.
cooper_nova
17-04-07, 10:14 PM
nice one ad!! you have to try and get in before pv :cool:
macc nova
17-04-07, 10:52 PM
very nice
Cba put it in before pv lol
Got a few bits together for the engine, new cambelt kit and clutch kit off ebay for a tenner lol.
Got most of the gaskets etc to put it back together too.
Also got the hammerite out :)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/blockpainted.jpg
The cam cover will be going satin black, as will the gearbox.
Dont think i'll fit the eco engine cover.
coochiSR
30-04-07, 05:57 PM
Not to sure about the blue block BUT looking good Ad, cheap as for the clutch and belt ;)
Blue blocks are cool :)
And thats the only hammerite i had lol
Sirnixalot
01-05-07, 11:36 AM
lookin good so far :)
cant wait to see it in its new home
(added you to msn, have some q's about the engine and conversion if you dont mind :thumb: )
looks mint mate, nice one!!
you need an inlet on the engine...
get rid of the crappy vaux one
Aye i know Ste.
Theres a copy type one on ebay for ?200 ish that i may get sometime.
But thats ?200 towards some tb's, Lol.
Sirnixalot-No probs.
Cheers for comments people :)
O, the cam cover is now satin black too,Lol.
make your own lol... cant be that hard?
nova sri inlet modded?
Maybe, but i only have a drill, file, and hacksaw,Lol.
If you want to have a crack at one, go right ahead, i'll happily test it :) Lol
pass, if i had time to funk around doing things like that, would of had my engine fitted by now lol
Finally got the gaskets and bits I ordered, so got on with getting the engine re-built up.
Got cambelt kit on and fitted, after a wee problem with the tensioner not holding still
http://img.photobucket.com/albums/v86/Nova-crew/16xecambelt.jpg
Also got the kent cams fitted, and the inlets, cam cover etc back on.
http://img.photobucket.com/albums/v86/Nova-crew/Paintedinletetc.jpg
Pretty much ready to fit.
Planning on fitting the weekend after pv.
all looks good ad. bet you cant wait to fit it! will be nice and quick!
but defo get some carbs on it in the future, i heard mine for the first time in a while yesterday and tere awsome as you no!
Cheers Lew.
Yeah, i'll deffo miss the carb noise, hence why i might save them for a rainy day,Lol.
Lookin good ad! i reckon you'll be wel chuffed with it.
On the inlet front, i once had a mantzel powerbox on the 1.4, and tbh the quality imo was shi*e. It fitted poorly, and the casting was crap. I reckon you could easily make one out of say, 4mm steel, and see the same results a a mantzel.
I was thinking of maybe going to a local engineering works with some drawings and seeing if they could make one up.
I'd probably see good power gains with 40s, but im back to the lower mpg etc situation then,Lol.
yeh defo keep yor carbs for a rainy day ; )
that would be nuts to drive i recon!
I was thinking of maybe going to a local engineering works with some drawings and seeing if they could make one up.
I'd probably see good power gains with 40s, but im back to the lower mpg etc situation then,Lol.
I've heard of bulkhead fouling issues too with carbs/trumpets on the x14/x16 too.
Have a go at the powerbox fella, i'l weld it up for you if necc, plus you can't beat the "having a go yourself and netting 20 bhp" feeling!
I ran an astra x16xel inlet pipe on mine, much smoother/direct than the oddly shaped corsa/tigra item.
My sell the 40s on then, and make plans for a inlet box.
Nice thread Ad, just sat and read it all. If I was to redo mine it'd be very similar to this!
Cheers Paul :)
Later this summer i might see about getting two arch lip repair panels fitted to completely sort the bodywork :)
Superb thread and update mate...car looks stunning...all the money spent in the right places;)...
Cant wait to PV to see this little beast in the flesh:)
chris
Cheers mate.
Just ordered some new number plates(the old ones are fooked, and mouldy(nearly failed mot on them,Lol)
Also got a Flat F13 type Flywheel to replace the hefty pot one that came on the 16v, saves about 4kg in weight.
Ive also made up a wiring loom, using the car side of the corsa ecu plug(so it plugs in), also spliced in the immobiliser pickup. Now just needs to be wired into the car(6wires), and everything should work. Might do the wiring sometime soon, as thats one less job to do when engine goes in, and it'll then just plug in :D
Just got to have the tyres put on the white Cesaro's and respray the bumpers, and it'll be sorted for pv.
Ive just refitted both wipers back on too, in place of the single wiper, got a bit annoying with the wiper half way up the screen. I might refit it if i can find a nice looking single wiper arm.
New plates have arrived, look much better than the old original ones.
Front bumpers been resprayed(haven't really got the weather to do the rear one :( ) So that'll stay as it is.
Got to get the mobile tyre fitter out here in a bit to get the tyres swapped onto the new rims.
Also, engine is completely built up, sorted the alternator situation, so it now runs a single V setup :)
Just need a gsi exhaust system now to make the downpipe hopefully bolt up when the engine goes in :)
nice work mate, cant wait to see it at PV
and as for the 40s, sell them me ;)
40s will be for sale after pv ;)
Might ebay them tho and hope for stupid money lmao
craig green
24-05-07, 12:10 PM
Just list them with a bonkers power claim... They'll go for a song!
so if i get you drunk at PV ill get them cheap ;) lol
LMAO
Im only going be there on the sunday :(
Just rung the tyre fitter, and he's fully booked till Tuesday.
So that leaves a few days before pv to make sure the rims hold air etc,Lol.
None, im removing the ones off my old rims lol
Pff, get some nice new ones.
Fcuk that.
Re-use the old, pikey style lol
novautd
24-05-07, 06:23 PM
just read the whole thread and your car looks mint, if the tyre fitter scratches ur rims get him to repair or replace them
Ive used him before, hes a good guy.
Hoping he'll take extra care,Lol.
Tyres are now fitted, and wheels are on. :)
He did quite a good job, no scratches on them, just a few black marks on the edge where the tyre slid over.
Piiiiiiiiiiiiiiiiiiiiiiiiiiiiics.
Cant get decent pics because of where the car is :(
Off out later to make sure they dont vibrate at speed etc,Lol.
Take some better pics then.
The finish on the centre caps isn't great :(, but it'll do.
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1032410006Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/P1013240002Medium.jpg
They look well good, you like 'em white?
Oh well I guess they're coming my way then lol
BigStan
29-05-07, 05:49 PM
They look good mate, look forward to seeing some proper pics !
Oh well I guess they're coming my way then lollollol
Im going clean the car, and get some decent pics later/tomorrow. :)
bieransri
29-05-07, 05:58 PM
i wasnt sure at first with my wheels, think white on white is quality now, i like em
Dan 130
29-05-07, 06:08 PM
look nice if not il buy them lol
Lol. They're staying on for now :)
wash it now and get some better pics :D
Lol, will have better pics tonight/tomorrow :D
vaughanmc
29-05-07, 07:53 PM
Looking good bud!
Note to self: Must get some Ceasaro's if i dont sell up lol
Aye, there quite a nice wheel.
O lookie, my old ones are sitting in the shed ;) lol
Aye, there quite a nice wheel.
O lookie, my old ones are sitting in the shed ;) lol
PM'd :thumb:
40s will be for sale after pv ;)
Might ebay them tho and hope for stupid money lmao
?420 i got for my Sport 40's with Irmscher Inlet and GM centre throttle linkage :D
Jesus christ, "Fires up ebay" lol lol
Jesus christ, "Fires up ebay" lol lol
99pence start, 10 day auction :D
I bought a gas flowed C14SE head for ?89, use it for about 1k mile with the carbs and sold it for ?180 lol 2 days after selling the carbs hahaha
coochiSR
29-05-07, 08:52 PM
Looking great Ad, better than i ever thought lol. I reakon you should take Cesaro's PV, make a mint there :D In giving them to me
Took some better pics today, im a big fan of the wheels now :)
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/White%20cesaros%20fitted/P1010002Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/White%20cesaros%20fitted/P1010006Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/White%20cesaros%20fitted/P1010013Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/White%20cesaros%20fitted/P1010014Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/Nova%20WIP%20pics/White%20cesaros%20fitted/P1010003Medium.jpg
looks good, perfer the wheels if they was in hurricane grey to be honest though ;)
looks good ad, only prob is the wheels look 'whiter' than the car if you get me
and ive spotted some rust :p
looks good ad, only prob is the wheels look 'whiter' than the car if you get me
There in Gloss White, thats why ;)
and ive spotted some rust :p
Rear arches? :( They need replacing :(
looks good ad, only prob is the wheels look 'whiter' than the car if you get me
I agree, they look lovely Ad, just a tad 'too' white.
Either that or the car needs a 40 degree cycle with some Vanish.
vaughanmc
30-05-07, 04:35 PM
Looking good mate I like them in white
Looks like a Nova Supertouring :)
I'll see what colour they turn after the brake dust eats in lol
Did 30mile today and couldn't see most of the spokes when i got home,Lol.
BigStan
30-05-07, 04:55 PM
Looks well nice mate, good job !
bieransri
30-05-07, 06:20 PM
look nice them. cant wait to get my smooth wings and spoiler fitted
Cheers :)
I just need engine in now
kevster
30-05-07, 06:24 PM
mint!!! nice work matey
Stokie_Dave
01-06-07, 06:32 PM
this is a stunning car, been chatting to ad for yrs but seen it for the first time today and been having a nosey on the net for a 2nd car, nice lil nova :D lol
lol
Cheers dave.
You can hear your corsa's exhaust from a mile off! Lol
a set of shorty mirror's would look mint on that adam :)
Im planning on either shorty mirrors or manta ones :)
Ive heard visibility is ****e tho.
visibility was fine on mine...
http://i10.photobucket.com/albums/a130/Ste_SRi/PVS06/PICT0015.jpg
http://i10.photobucket.com/albums/a130/Ste_SRi/PVS06/PICT0010.jpg
Cool, might get a spare set of mirrors and see if I can make some.
gary_126
05-06-07, 12:31 AM
looks sooo much better with the white wheels!
Engine looks spot on!
Were you at pv with it? never saw it (but then agin there Were millions of cars there)
You should put the twin 40's on the xe, would sound awesome, and give good gains
Yes mate it was at PV.
http://img.photobucket.com/albums/v86/Nova-crew/PVS%202007/DSC00218Medium.jpg
The car currently looks like this lol
http://img.photobucket.com/albums/v86/Nova-crew/Engineremoval.jpg
Putting the new 1.6 in it? Good man.
haha you now feel the wrath of white wheels! two seconds out the road and they'll be filthy! when there clean you gotta love 'em though!
There completely black atm, cba clean them.
Maybe for next years PV lol
Engines out
http://img.photobucket.com/albums/v86/Nova-crew/P103242310001Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/P1234010004Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/P1013250005Medium.jpg
http://img.photobucket.com/albums/v86/Nova-crew/P102343210006Medium.jpg
Spraying the engine bay tomorrow and sorting out the old spi wiring. :)
Superb mate....seen it at PV got a few pis...but my memory card decidedtto erase the days pics and vids....stunning wee car..
chris
Cheers mate :)
Bay is now resprayed, engine should be in tomorrow.
good work but, poor 8v :cry:
Die 8v, Die lol
Tis a shame tho, that engine has had a few inlet,exhaust,head swaps in its time, and never let me down once. Now its sitting depressed in the garden :(
now it'll look like my car lol
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.