Stuart
19-11-06, 07:15 PM
to start off i WILL NOT POST ANYTHING.... well ok i will but postage will be charged at ?250 lol
Basically ive totally lsot intrest in the project, as im not willing to spend the extra to make it handle like my daily
drive etc.. I'd like to sell the entire car+ bits in one go. it needs 2-3 weekends work to get it finally running. ?1250
takes the car as it sits right now (less the tools inside lol) its either got the following fitted, or sat inside it.
pics will follow eventually.. but some can be found here http://www.novaload.net/forum/viewfeaturecar.php?ref=2949
Wheels/Tyres
4* 13*5.5" Softstars.. no tyres, few sratches etc but they run true. ?40
4* 185/50/13 Avon ACB10's barely worn. ?80
there are some 13" slicks that i cant remember the exact dimensions of, they are used but tons of life left.. ?40
a pair of very worn 14" A048's ?10
4 * nasty 14*5.5 alloys ?20
Brakes
2* brembo xdrilled 236*20mm discs (to suit gte/gsi/sri calipers) not used but a bit of surface rust. ?40
1 set of Mintex M1155 pads to suit ATE GSI/SRI 236mm*20mm disc/calipers.... also fits in 256*20mm calipers from corsas New
but fitted never used ?50
Nova twin Master cylinder bias pedal box with cylinders that have integral reserviours (used before i got hold of it) SOLD
Full braided brake lines + fittings to suit the bias box (single fluid line to rear of car, plits on rear beam etc) SOLD
Suspension
pair of old sheddy avo coilover shocks + random springs.. dire need of a refurb.. ?20
Koni ajustable shocks front + rear(with travel limiters for small rear springs) used before me.. ?40
Random selection of springs front + rear.. no idea whats what. ?40
home modded nova TCA's with plates to fit adjsutable lentgh tie bars + front brackets to fit... never tested so no idea if
they work lol + red rally design TCA bushes ?60
Quick rack with new tie rod ends (temporarly reserved but if its not wnated then its FS)
Rear beam, was stripped right down, cleaned up and hammerite slapped over it (some chipping though), rebuilt with red poly
bushes, NEW drums, NEW bearings, NEW shoes + springs, NEW wheel cylinders, NEW HB cables, never "used" ?80
Stud conversion kit + nuts New, fronts fitted, rears not. SOLD
Body work
Would prefer to sell the shell in one piece but if need be then parts can be removed at cost below.
Shell is seam welded in the bay and certain points down the chassis, ALL unnessecary brackets removed from rear seat
mounts, dash mounts etc. any rot fixed, new rear pannel, spare wheel well removed and X braced, doors were fully stripped
back to metal a tiny piece of rot was fixed and then they were rust proofed etc then sprayed with the shell, they ahve been
hole sawn BUT will still take full window winders etc passenger door is delocked with metal plate. Shell is generally
Glacier white, with the A/B/C pillars being kings blue, same as the front wings. Bootlid has been gutted and delocked +
resprayed and has 2mm polycarb bonded in and pinned on. Drivers side has rails mounted for bolting a seat to. Rear cage
only, saftey devices one. sprayed to match shell.... its less than likely to be a rolling chassis... ?500
Rear MK1 gte bumper, sprayed in Calypso red, with iron removed and body pints fitted. ?20
Gte/GSI side skirts, sprayed in Calypso red, NO CLIPS ?20
front MK1 gte bumper, red/white and blue painted... irons removed for body pins ?20
Mamba 5 slot wide bucket seat.. bottom mount, black/blue ?40
TRS nascar 5 point harness, black ?40
Engine/Gearbox
Oh this will be fun... not
the silly 1.2 engine... id rather not split it up as im lazy.
the spec is
1200 block + 0.5mm overbore L&B bottom end De-seamed and shot peened rods Arp bolts Mew rings and bearings and seals obv
Pistons with deeper pockets to allow lairyer cam, possibly high compression too Block decked 1.2 head with 1.6 sized valves
cut in Gary head work (matching cut in valves and trimmed guides down) Nearly 2mm skimmed off it (need to be carefull about
spark plug choice its that close) 303degree flat nosed cam ground to suit clearences from Catcams (thanks rob) Solid lifter
conversion (welded) Shimed to suit clearence "home" made vernier pulley (kidney slotted std pulley) 1.4 bosch dizzy +
powertrain coil Some random tripple electrode NGK plugs that have the same heat rating but a tad shorter than the
recomended std ones. Weber T40's on irmchser fannymould 1.2 Flywheel, std weight to try and maintain intertia lol 1.6
friction plate omp uprated version Solid engine mounts, well ok one is a proper mount and the other 3 are silicone adjusted
ones ?500
ashley 4-1 manifold (wrapped and painted) + system and new rubber mounts ?100
gearbox is an F15 case, with an F13cr cluster and a 4.29 fd (NO i will not split the fecking box up) ?100
armtech coil mount rev limiter SOLD
facet interupter fuel pump ?20
filter king pressure regulator and pressure gauge and filter all in one.. ideal for carbs (not injection) NEW ?30
Other stuff
Dash pannel with rev counter, some nova dials and all switches needed to run an engine+lights etc includes a cheapo
immobiliser ?20
Theres probably more but i cant remember off the top of my head.
ill take paypal, cash, cheque, bank transfer, xbox 360 games, booze, fuel, etc lol
i live in ware.. can meet at say baslidon and now and again solihull
Basically ive totally lsot intrest in the project, as im not willing to spend the extra to make it handle like my daily
drive etc.. I'd like to sell the entire car+ bits in one go. it needs 2-3 weekends work to get it finally running. ?1250
takes the car as it sits right now (less the tools inside lol) its either got the following fitted, or sat inside it.
pics will follow eventually.. but some can be found here http://www.novaload.net/forum/viewfeaturecar.php?ref=2949
Wheels/Tyres
4* 13*5.5" Softstars.. no tyres, few sratches etc but they run true. ?40
4* 185/50/13 Avon ACB10's barely worn. ?80
there are some 13" slicks that i cant remember the exact dimensions of, they are used but tons of life left.. ?40
a pair of very worn 14" A048's ?10
4 * nasty 14*5.5 alloys ?20
Brakes
2* brembo xdrilled 236*20mm discs (to suit gte/gsi/sri calipers) not used but a bit of surface rust. ?40
1 set of Mintex M1155 pads to suit ATE GSI/SRI 236mm*20mm disc/calipers.... also fits in 256*20mm calipers from corsas New
but fitted never used ?50
Nova twin Master cylinder bias pedal box with cylinders that have integral reserviours (used before i got hold of it) SOLD
Full braided brake lines + fittings to suit the bias box (single fluid line to rear of car, plits on rear beam etc) SOLD
Suspension
pair of old sheddy avo coilover shocks + random springs.. dire need of a refurb.. ?20
Koni ajustable shocks front + rear(with travel limiters for small rear springs) used before me.. ?40
Random selection of springs front + rear.. no idea whats what. ?40
home modded nova TCA's with plates to fit adjsutable lentgh tie bars + front brackets to fit... never tested so no idea if
they work lol + red rally design TCA bushes ?60
Quick rack with new tie rod ends (temporarly reserved but if its not wnated then its FS)
Rear beam, was stripped right down, cleaned up and hammerite slapped over it (some chipping though), rebuilt with red poly
bushes, NEW drums, NEW bearings, NEW shoes + springs, NEW wheel cylinders, NEW HB cables, never "used" ?80
Stud conversion kit + nuts New, fronts fitted, rears not. SOLD
Body work
Would prefer to sell the shell in one piece but if need be then parts can be removed at cost below.
Shell is seam welded in the bay and certain points down the chassis, ALL unnessecary brackets removed from rear seat
mounts, dash mounts etc. any rot fixed, new rear pannel, spare wheel well removed and X braced, doors were fully stripped
back to metal a tiny piece of rot was fixed and then they were rust proofed etc then sprayed with the shell, they ahve been
hole sawn BUT will still take full window winders etc passenger door is delocked with metal plate. Shell is generally
Glacier white, with the A/B/C pillars being kings blue, same as the front wings. Bootlid has been gutted and delocked +
resprayed and has 2mm polycarb bonded in and pinned on. Drivers side has rails mounted for bolting a seat to. Rear cage
only, saftey devices one. sprayed to match shell.... its less than likely to be a rolling chassis... ?500
Rear MK1 gte bumper, sprayed in Calypso red, with iron removed and body pints fitted. ?20
Gte/GSI side skirts, sprayed in Calypso red, NO CLIPS ?20
front MK1 gte bumper, red/white and blue painted... irons removed for body pins ?20
Mamba 5 slot wide bucket seat.. bottom mount, black/blue ?40
TRS nascar 5 point harness, black ?40
Engine/Gearbox
Oh this will be fun... not
the silly 1.2 engine... id rather not split it up as im lazy.
the spec is
1200 block + 0.5mm overbore L&B bottom end De-seamed and shot peened rods Arp bolts Mew rings and bearings and seals obv
Pistons with deeper pockets to allow lairyer cam, possibly high compression too Block decked 1.2 head with 1.6 sized valves
cut in Gary head work (matching cut in valves and trimmed guides down) Nearly 2mm skimmed off it (need to be carefull about
spark plug choice its that close) 303degree flat nosed cam ground to suit clearences from Catcams (thanks rob) Solid lifter
conversion (welded) Shimed to suit clearence "home" made vernier pulley (kidney slotted std pulley) 1.4 bosch dizzy +
powertrain coil Some random tripple electrode NGK plugs that have the same heat rating but a tad shorter than the
recomended std ones. Weber T40's on irmchser fannymould 1.2 Flywheel, std weight to try and maintain intertia lol 1.6
friction plate omp uprated version Solid engine mounts, well ok one is a proper mount and the other 3 are silicone adjusted
ones ?500
ashley 4-1 manifold (wrapped and painted) + system and new rubber mounts ?100
gearbox is an F15 case, with an F13cr cluster and a 4.29 fd (NO i will not split the fecking box up) ?100
armtech coil mount rev limiter SOLD
facet interupter fuel pump ?20
filter king pressure regulator and pressure gauge and filter all in one.. ideal for carbs (not injection) NEW ?30
Other stuff
Dash pannel with rev counter, some nova dials and all switches needed to run an engine+lights etc includes a cheapo
immobiliser ?20
Theres probably more but i cant remember off the top of my head.
ill take paypal, cash, cheque, bank transfer, xbox 360 games, booze, fuel, etc lol
i live in ware.. can meet at say baslidon and now and again solihull