View Full Version : Advice Needed: Tailpipes
Big_Chap
03-02-06, 04:31 PM
i'm looking at replacing my exhaust and i am a little unsure of the tailpipe design, i'm think either the same as i have now or twin 3" or 3.5" outwardly rolled, both centred? also though about moving to to the left to be different but theres too many fuel components above!
any suggestions?
PS. the heat sheild is getting ripped off too.
http://img.photobucket.com/albums/v82/Big_Chap/d07742e7.jpg
Hellllloooo... I spy ST185
Philsutton
03-02-06, 05:05 PM
must be at a gay bar then
Lee-Gsi
03-02-06, 05:26 PM
single 3 inch pipe mate, would look the dogs nads.
Single or Twin 3" i would go for.
Car looks great btw, its made me want to colour code my gsi bumpers now,lol.
novatek
03-02-06, 05:50 PM
i vote 3" inward roll, on the left of the bumer tho
Just for reference this is a 3" round
http://img.photobucket.com/albums/v485/DPursey/DSC03047Small.jpg
I'd say single 3" inward rolled on both sides (as in twin pipes on each edge).
-Bruce-
03-02-06, 07:17 PM
I would say 3" inward rolled but on the left as normall.
P.S long time no see mate. Prob see you in falkirk in the summer
Bruce
I'd say single 3" inward rolled on both sides (as in twin pipes on each edge).
I photoshopped this idea on my car and it looked rubbish.
If you're keeping a standard bumper I'd suggest getting a twin 3" put back on the left hand side.
Jim
I photoshopped this idea on my car and it looked rubbish.
Really? Hmm, I thought it would have looked ok :(
Do you still have the pic, Jim?
FlatBeatBoy
03-02-06, 08:53 PM
I photoshopped this idea on my car and it looked rubbish.
If you're keeping a standard bumper I'd suggest getting a twin 3" put back on the left hand side.
Jim
Yes because everyones idea is rubbish compared to yours?
Your idea is ****ing **** as well hope you choke on something like a c0ck
Single or Twin 3" i would go for.
Car looks great btw, its made me want to colour code my gsi bumpers now,lol.
Noooooooooo.
I'd go for a 3 inch inward rolled tailpipe but off to one side, mate keep it subtle.
chris gsi
04-02-06, 01:04 PM
i got a 3inch oval on my gsi and it suit's it
Big_Chap
04-02-06, 01:05 PM
I would say 3" inward rolled but on the left as normall.
P.S long time no see mate. Prob see you in falkirk in the summer
Bruce
was there on thursday in the nova, ain't been through in it for about a year and a half.
i got a 3inch oval on my gsi and it suit's it
any pics?
i was tempted to put it back on the left as i feel the twin would look better at the side than in the centre but it seems a shame to ignore the work involved in creating the centre exit. i do think that the one on the now is probably the best style for a centre exit but just want to see others opinions are. :thumb:
chris gsi
04-02-06, 01:17 PM
i have on pvgevents.net or pm me your mobile number and i will send you a pick
orange_andy
04-02-06, 04:30 PM
i think the circle pipe in the centre looks LIKE dogs bollocks tbh, the more square one looks ok, im not keen on a single pipe though unless it fits in with the style and look of the car, each to there own tho
chris gsi
04-02-06, 07:27 PM
http://i45.photobucket.com/albums/f57/chris_1981/nova6.jpg
Give it some rev
04-02-06, 10:42 PM
i think it looks ok now. it sits nice and close 2 the bumper :)
Really? Hmm, I thought it would have looked ok :(
Do you still have the pic, Jim?
Yeah, somewhere, I did 3 different rough shops to see what it would look like, I'll upload them later.
Yes because everyones idea is rubbish compared to yours?
Your idea is ****ing **** as well hope you choke on something like a c0ck
Erm, ok. Not sure what your problem is, was just giving my own opinion on something. Perhaps the word "rubbish" is wrong, but it didn't look right. Maybe it's because I have a novadose rear? Again, I'll post the "shops" up later and you can decide for yourselves.
Jim
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.