some new pics of car......

[david dixon]

was working on it yesterday so i thought i would show you some pics of it!


http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/05a1.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/backpic1.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/backpic.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/boosttemp.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/bgauge.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/DSCF0004.jpg

And some new parts to go on when i finish the phase 5 engine.

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/05b1.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/05b6.jpg

http://img.photobucket.com/albums/v84/nova-turbo/My%20nova%20pics%20new/05b8.jpg

Hope you like them! :D

[dan16v]

very nice m8! cant believe you leave the poor thing outside!
that manifold is a bitch to do! poss the worst job i had to do on my car :lol:
hope you enjoy grinding :D

[david dixon]

very nice m8! cant believe you leave the poor thing outside!
that manifold is a bitch to do! poss the worst job i had to do on my car :lol:
hope you enjoy grinding :D

yeah me and my mate have them manifolds and we've been trying think which way is best! might be going to cut the flange between the pipes and match them up to a ex flange and redrill the holes, not sure yet. :D

[dan16v]

i just disk cut like you said in between each runner. then disk cut as close to the runner as poss and finished off with a grinding wheel to take all the nissan flange off!

[luke langton]

Nice manifold you got there, what car does it come from? (Nissan) I would like to get a new one too, for my E16SE turbo. Do you know if I could get something similar?

[mark1astramad]

FAIR DOS MATE,THE INTERIORS FAPPIN MINT
REALLY NICE CAR
KEEP IT UP :D

[Mike.]

like this car alot, nice colour

[david dixon]

Nice manifold you got there, what car does it come from? (Nissan) I would like to get a new one too, for my E16SE turbo. Do you know if I could get something similar?

Its a nissan 200sx aftermarket manifold, you could make it fit the 16se but the turbo that fits might be to big for the engine (T28) but you could change the flange!

[raza]

nice as fuck :D

[luke langton]

Ok thanks, yeah that turbo would be too big as I have a t2 at the moment but as you said I could cut the flange. Where did you get it from? And how much are they?

[Mike.]

think it would look better with a square front plate on the front though

[david dixon]

Ok thanks, yeah that turbo would be too big as I have a t2 at the moment but as you said I could cut the flange. Where did you get it from? And how much are they?

bought it off internet.

iv got a square plate for the front but just haven't put it on yet!

[Snowface]

nice.
why've you got 2 speedo's?

[david dixon]

nice.
why've you got 2 speedo's?

I dont mate, the 6 speed box is one of the later types and doesn't have a speedo drive so i bought the other one, also does 0-60, 1/4 mile and top speed recall!

[-=VanMan=-]

Have you mounted your boost gauge in your actual clock or removed it and used something else to mount it too?

:?:

[srs1]

car looks like a right sleeper.
i shall be noseing around it at york
:D

[david dixon]

Have you mounted your boost gauge in your actual clock or removed it and used something else to mount it too?

:?:

I just removed the clock and opened the holder out a bit and the gauge just fitted in nicely. :D

[Riggy]

looking really nice there mate :lol: