new brake's are on....

[benji]

but the wheels don't bloody fit.

i fitted my new wilwood's on saturday, just need to bleed the system again when i get 5 min's. the wheels caught on the bottom of the caliper where the spokes come into the center of the wheel. i had to get some 5mm spacers to make them fit. sonow i'm on the lookout for some comopmotives mo's or TH's or some team dynamic's pro race's.

the spacers i was sent for the disc's didn't fit, so they will need sorting out, i will ring rally design in the morning.

i got a few pic's

http://homepage.ntlworld.com/bencurry/brakesfitted.JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(1).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(2).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(3).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(4).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(5).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(6).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(7).JPG

http://homepage.ntlworld.com/bencurry/brakesfitted(1b).JPG

[Matt Nova]

looks mint mate nice one

[Mike.]

they look really good, shame about the wheels not fitting

[nova_kev]

i have ordered some pro races, but they have discontinued the pro race 1's which weighed 6kilos each.

ordered the new 1.2s :wink:

[Dar]

Looking nice Benji :D

Although have you fitted them upside down? What looks like the bleed nipple is pointing towards the ground.

[SKoob]

Look really good mate, making me reconsider my choices before I get my new brake setup :)

[Adam]

They look mint benji.
Which wheels have you got on, the fox's.?

[Philsutton]

looking very nice there, got a good little track now

[krobinson]

Look fantastic mate.

Pity they dont fit with your alloys, but i think a new set will look even better!

Keith

[J4MES]

they look well nice should stop well, when u get the wheels on..lol :lol: :lol:

[rhs98]

Looks good - if you don't mind me asking - how much did that cost?

[~~joycey~~]

must be big brakes if 15's dont fit :o

[benji]

they are upside down, i fitted them as the box said. but i have since been told they are the wrong way up.

they cost ?450

[rhs98]

8) ?450 is a good price!

[nathan.]

nice one ben. you getting ready for donington. what you doing about your wheels then?

[benji]

i don't have a clue what to do about the wheel's. although i have been told i can borrow a set of et35's if i need to.

hopefully i will be able to get some private work in. a couple of saturday mornings should get me a new set of alloy's and tyres

[nathan.]

a couple of saturday mornings should get me a new set of alloy's and tyres

bloody hell, how much do you charge? :lol: :lol: :lol: :lol:

[benji]

depend's what the job is, if it's a mains change that's ?250-?350 depending on what's involved. any other work and i try to fit it in on a evening cause it usually don't pay enough to be worth getting out of bed for on a saturday. lol.

[nathan.]

lol. im in the wrong trade :roll:

[benji]

what do you do?

[m.d.]

fookin ell. i dont get paid 250 in a week normally. and im a fully qualified toolmaker/engineer.....


those willwoods look spot on mate. did the spacers not fit over the hub or something. as i can see they fitted the disc. im getting the exact same set up soon so ull have to tell me how they work.

[benji]

when fitted the push the disc out too far so the caliper don't line up

[m.d.]

could you not just put that washer imbetween the calliper and spacer. would push the calliper out then to where you want. thats how you have to mount push bike and motorbike callipers,

or get the spacer machined thiner. and foot rally desighn the bill lol

[benji]

the point is it's a kit that should fit a nova. and it don't

[Riggy]

:lol: looks absolutly spunking gorgeous ben :lol:

[nova ian]

there some monster brakes :D

top stuff, keep it up, shame your wheels didnt fit, hope you sort it