twin 40s

[Mr.h.]

can i just bolt these on and b ready 2drive away or do i need 2 do other things such as a cam? :roll:

[peester]

firstly list youre car, spec, mileage, general condition; as much about ur car as you can. then tell us what twin 40's-wise you have; are they new, just two carbs? no linkage/manifold etc?? won't get no replies with just what youve sed. then we can start to help.

[mikeoxford]

big thing id say (from experience)

is not only get the correct inlet manifold - get it port matched.

RR prooved that from running a incorrect inlet that i had machiend as close as i could to my head - to the correct inlet manifold, exactly port matched

15 BHP

yes - fifteen. thats a lot in my book for something thatll cost you ?80 to get done right :!: (including manifold if you look hard enough)

[S_Gault]

I put every engine i do on the rollers/ dyno as setup alone is worth power.

Steven

[cooper_nova]

can i just bolt these on and b ready 2drive away or do i need 2 do other things such as a cam? :roll:

also do they come wiv the throttle linkage??

[Mr.h.]

sorry lads i didnt give much info on them did i :oops: i aint got them yet there on ebay i spoke 2 the owner he said i can have them 4 ?200 they come on a manifold and with all the linkage + trumpets! he says they "SHOULD" FIT? IF U COULD HAVE A LOOK AT THGEM 4 ME N LET ME KNOW IF THERE OK? I DONT NOW HOW 2 POST THE LINK SORRY!HE SAID THEY WERE LAST ON A RUNNIN CAR ABOUT A MONTH AGO?CHEERS 4 ANY RESPONSE ITS VERY HELPFUL OF U ALL :D

[Mr.h.]

MY CAR IS A 13SR MK1 NO ENGINE MODS! :oops:

[cooper_nova]

to post the link go to the page of the item u want to post then highlight the web addy bar and then right click>copy. then get onto this topic and post a reply then right click>paste and voila!!!

hope this helps mate
:D

[Mr.h.]

these r the little beautshttp://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=2476933402&category=10404&sspagename=STRK%3AMEBBI%3AIT&rd=1

[Mr.h.]

these r the little beauts http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=2476933402&category=10404&sspagename=STRK%3AMEBBI%3AIT&rd=1
sorry about this im new 2 computers :oops:

[cooper_nova]

its not working mate try again

:oops: posted this while u posted the link again oops!

[cooper_nova]

just looked at the link and they look good come wiv all the bits u need by the looks of things, try and get them as cheap as u can coz u'll want to get a rr setup session done

[Richyb]

make sure you save some money for the rollin road session cus it cost me 142 quid when i had my 1.4sr.... that was partly becus the carbs had come of 1600 and needed different jets and 2 hours of settin up. a decent set up will prob cost you 80-100quid if they have the correct jets

[novasportjersey]

go to http://www.pccuk.net/default.htm?page=377 for the nova sport jet sizes give u a good starting point. different manifold and airbox may mean some adjustment required but wont be far off!

[S_Gault]

post your spec and I'll give you starting points..

I worked for weber for 5 years before I went out on my own.

Steven

[Mr.h.]

the twin 40s didnt go 2plan the chap i was gettin them off messed me about? got a 32/34 now but this happened last night http://www.novaload.net/forums/viewtopic.php?t=92819