PDA

View Full Version : Small block parts needed. List to be updated at regular points.


TeddyThom
29-10-13, 10:06 PM
Hey all, work is finally paying off. So I need some parts for the nova. All parts in blue, I want asap, all parts in red are on the wishlist for another payday/suitable price, depending on negotiations.

I also have a for sale thread, I am open to offers and trades. If you see something you like, and want to swap etc, by all means drop me a PM. Thread is here: CLICKME (http://www.pngclub.com/forum/showthread.php?197794-Mark-2-bits-and-pieces-plus-turbo-diesel-engine-and-loom)
Set of driveshafts. 22 spline outer cv's and small block inner cv's please. Just found out mine are fubar'ed. Or even a set of standard small block driveshafts please.
Headlight switch for a mark 2 dash as I got a bit annoyed with mine as it didn't want to move lol
Gear gaitor. Any considered, would prefer original but WHY.
Cash waiting :)

Front strut brace
KENT AS2 cam
Rear disc beam with all the trimmings i.e: all set up so I can just bolt straight to the nova
Suitable discs and calipers for rear disc beam
Cash may be available for these today depending on prices and what cash I have left. No immediate rush for these items.
dgbnova#1
29-10-13, 10:17 PM
Should have alty here and got a strut brace also could do with a re paint
TeddyThom
29-10-13, 10:27 PM
What's your prices dude? Need them posted. Should've mentioned that really lol my bad. Need them posting to me15
johnd
29-10-13, 10:30 PM
simontw is selling a rear disc set up mate
kent14sr
30-10-13, 05:51 PM
I have a complete rear disc beam, and also brand new discs to go with it. Also have correct reducing valves too. PM if of interest.

Have plenty of alternators and used cam followers.
TeddyThom
02-11-13, 05:43 PM
Bttt :)
dgbnova#1
02-11-13, 05:58 PM
Got a head here for that what engine is it 1.6
dgbnova#1
02-11-13, 06:03 PM
Sorry it's 1.4 just seen it on the casting my 1.6 should be the same I'd say anyone know? I'm sure it is
TeddyThom
02-11-13, 07:07 PM
Yeah I need the 1400 head, if I have a 1600 head my compression will be too low lol

If I can't find a 1400 head then I want the 1200/1300 head as long as the ports match up
dgbnova#1
02-11-13, 10:19 PM
Are you 100% on that as I thought all 14 16 were interchange as per the articles on here
TeddyThom
03-11-13, 11:35 AM
I'm basing my build around this article here: CLICKME (http://www.pngclub.com/forum/showthread.php?93430-*INFO*-1-4-8v-Tuning-Guide)

Or I will be at any rate. Main priority is get it running, so the 1400 head is what I need. Anything smaller (with matching ports) is a bonus.
Alex J
03-11-13, 08:14 PM
got a full piper high lift cam set here and rebuild kit for a 1.3sr here if thats any good??
TeddyThom
08-11-13, 03:40 PM
Bump for fresh parts.
Peredur
08-11-13, 06:53 PM
Got a 1.4 big valve head here
TeddyThom
09-11-13, 07:38 PM
No need for a head now. Thanks anyway. Bumpy bumpy!! Need a distributor asap please!!
TeddyThom
12-11-13, 09:26 PM
Bttt! :)
wwinstanley
13-11-13, 09:44 AM
No need for a head now. Thanks anyway. Bumpy bumpy!! Need a distributor asap please!!

What type distributor do you need? Have a few here, might have the right one.
TeddyThom
13-11-13, 10:18 AM
Delco remy slot type drive please dude
TeddyThom
21-11-13, 05:44 PM
Bump! :)
TeddyThom
25-11-13, 09:02 PM
Bttt! New parts added!