View Full Version : Wheel dilemma
steveo135
06-09-13, 04:11 PM
Just got back from powder coaters and fitted my new wheels to the nova, nightmare they are to wide.
Speedline turbines. 15"
195/45/15
Is their anything I can do??? Really like the wheels. Fitment is 100 pcd so that's ok. Is it worth having my rear arches rolled???
Or shall I sell them????? If so what are worth.
I will post pic up shortly.
steveo135
06-09-13, 04:14 PM
http://i1290.photobucket.com/albums/b521/stebez10/null_zps762984e0.jpg
steveo135
06-09-13, 04:33 PM
Think so. But think they fit most most with the fitment. Only got them back from powder coaters today.
Marcusgeorge
06-09-13, 05:03 PM
Presumably the tyres are rubbing ??
steveo135
06-09-13, 05:08 PM
Yeah on the rear arches.
Roll the arches. What offset are they?
Need some nice wheel bolts and a center/dust caps.
steveo135
06-09-13, 05:31 PM
I have the wheel centre. Thing they Are et 38
ET38 on a hatch is never gonna be good... Roll your arches will help. Or get the offset machined a bit...
How wide are they?
steveo135
06-09-13, 05:37 PM
Think they are 6 1/2
Find a machinist and get the ET machined, Closer you ae the 49 the better. But iirc Mazz runs 7J on a ET 45.
steveo135
06-09-13, 09:13 PM
Any machinist in blackpool that do this???
remove the 195's and get something thinner!
steveo135
06-09-13, 09:40 PM
Will that work????
is it a performance car or a looker?
steveo135
06-09-13, 10:13 PM
A looker, but has a 2.0 redtop, cage, Striped out. Going to be a daily driver.
8valve-craig
06-09-13, 10:28 PM
They are also not called Speedline Turbines. They are Speedline Maracanna's.
I very much doubt you will ever get them to comfortably fit a Nova hatch.
'Clio Turbines' as found on the ph1 16v. If it helps.
A few people used to run the ph2 wheel. I don't know what butchery that required, if any.
8valve-craig
06-09-13, 11:00 PM
Whatever people call them, quite like "cesaros", they have a name.
Whatever people call them, quite like "cesaros", they have a name.
Yeah, the name you call them in probably the correct one.
I was just helping the lad out, if he didn't know what they were from, so he would have more luck with ET and fitment Googling etc.
8valve-craig
06-09-13, 11:18 PM
Oh fair shout.
I have a set in my collection, pretty sure mine are 6 1/2j x 15 et38 too.
As already stated if its just a looker you might get away with a 165 tyre, but it will be a stretch and not very sensible. I tried one on the rear of my nova hatch with a 195/45 fitted and coundn't even let it fully off the jack.
steveo135
06-09-13, 11:38 PM
Ok, think ill just sell them. Not to sure of the correct model of wheel, but they are made by speedline as its stamped on the wheel. Seen a couple of set of these on eBay by the name of speedline turbines.
When fitted they don't rub only under load they catch. Shame really as they are a good looking wheel.
8valve-craig
07-09-13, 07:18 AM
Do you have the centre caps? If so the wheels will sell well. Refurbished ones with tyres occasionally fetch £300.
steveo135
07-09-13, 12:24 PM
Have all 4 centres. Freshly powder coated this week. All tyres have very good tread.
BRoadGhost
07-09-13, 12:43 PM
You can always take some off the face of your rear disks, combined with having the inside of the wheels machined down.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.