View Full Version : mounting bucket seats to nova frames
turbojolt
09-02-13, 01:21 PM
right i want to use the bucket seats original sliders on the bottom nova seat frames
as the buckets sliders are much narrower then the nova frame, i want to run steel across the width of the nova frame, bolt it down and then drill and bolt the seats to the metal
dont know if you guys think this is safe or not, seems a safe enough plan to me, and its got to be stronger then my **** welds lol
i will be using locklite and or nylock bolts where ever possible aswell
what thickness steel should i be using to do this?
Jon_nova1
09-02-13, 03:04 PM
you want to use some kind of box section 25x25x3mm ish I used 2x1 section when i did similar
turbojolt
09-02-13, 03:09 PM
that will make the seat sit to high wouldnt it, you got any pictures?
Jon_nova1
09-02-13, 03:47 PM
just the one on here
http://www.pngclub.com/forum/showthread.php?176378-Ferrari-red-TDI-nova&highlight=
The problem being if it's too narrow it'll flex, you'll be able to go narrower if there's no room to flex
not being rude but if your worrying about it sitting too high, get some proper mounts i,e the recaro ones or whatever and use them. i welded my old cally turbo heated leathers to nova frames and it sat alot higher up than standard nova seats, as in my head touched the roof lining if i sat up properly lol
turbojolt
09-02-13, 07:06 PM
the way i was thinking of doing it with a flat bar the seat would have proberly sat lower then a standard nova seat tbh, i just think having a 1" box under the seat and then a frame on top of that will be really high
i did looked at tailored frames to mount the seat, but if i remember right they were over 150 quid each!! so i wont be buying them mate lol
the way i was thinking of doing it with a flat bar the seat would have proberly sat lower then a standard nova seat tbh, i just think having a 1" box under the seat and then a frame on top of that will be really high
i did looked at tailored frames to mount the seat, but if i remember right they were over 150 quid each!! so i wont be buying them mate lol
http://www.ebay.co.uk/itm/BUCKET-SEAT-SIDE-BRACKETS-MOUNTS-OMP-SPARCO-CORBEAU-TRACKDAYS-RALLY-NEW-PAIR-/130723936162?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item1e6fc0f7a2 :thumb:
turbojolt
09-02-13, 07:54 PM
i dont understand them mounts, as my seats dont have anywhere on the sides to attach them :confused:
i dont understand them mounts, as my seats dont have anywhere on the sides to attach them :confused:
what seats you got mate?
turbojolt
09-02-13, 08:44 PM
i dont know what model they are tbh, like most of my project ive kept costs down by buying 2nd hand
http://sphotos-f.ak.fbcdn.net/hphotos-ak-snc6/251971_10150987161787118_554548999_n.jpg
seeing as there a known make surely they should have some holes for side mounts?
turbojolt
09-02-13, 09:02 PM
there fabric all down the sides mate :confused:
give me a min and i will take a picture
turbojolt
09-02-13, 09:13 PM
right pulled oner out of the wardrobe, this is a side veiw with the orignal bottom sliding mount removed
http://sphotos-d.ak.fbcdn.net/hphotos-ak-ash3/65542_10151424521542118_1925971678_n.jpg
What you're wanting to do is exactly what i've done with my Cobra Monaco's. They are very solid and secure:
http://i287.photobucket.com/albums/ll121/liampoulton/Liams%20Nova%20Build/IMG_2663.jpg
http://i287.photobucket.com/albums/ll121/liampoulton/Liams%20Nova%20Build/IMG_2665.jpg
turbojolt
09-02-13, 09:43 PM
so what kinda steel did you use mate?
turbojolt
09-02-13, 10:53 PM
im just going to take a punt at 3mm and go from there.
im just going to take a punt at 3mm and go from there.
personally id use 5mm, but thats just me. them bases look completely different to the ones i used so it should sit fine, therefore ignore what i previously said lol
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.