20xe Tuning bits. Wossners, Piper cams, Verniers, Springs, Caps, Head etc

[8valve-craig]

Due to recently purchasing a built engine with a far better spec than i had planned this lot is now surplus to requirements.

GM Cylinder head with a fair bit of port work done, No damage, had a skim or 2 but plenty left

£110

http://i995.photobucket.com/albums/af79/smith9051/006-2-1.jpg


http://i995.photobucket.com/albums/af79/smith9051/004-2-1.jpg

Wossner 12.5-1 full race pistons. Part numbers 9005da, Never used, complete with all rings and pins. 86.0mm,

£250. Can be supplied with a family 2 block @ 84.7mm which can be bored to 86.0mm for a brand new standard bore, for a little extra cost.

http://i995.photobucket.com/albums/af79/smith9051/260120121593.jpg

http://i995.photobucket.com/albums/af79/smith9051/Nova%20on%20bike%20carbs/04102012367.jpg

Jenvey dcoe style inlet manifold to suit either FWD carbs or TB's

£SOLD

http://i995.photobucket.com/albums/af79/smith9051/008-5.jpg

Piper BP300H cams. Brand new in packet, never opened despite the box being a bit tatty.

Ground from blanks and suitable for hydraulic lifters.

£300

http://i995.photobucket.com/albums/af79/smith9051/28102012838.jpg

http://i995.photobucket.com/albums/af79/smith9051/28102012839.jpg

Piper double valve springs, New in the packet.

£SOLD

http://i995.photobucket.com/albums/af79/smith9051/28102012840.jpg

Piper steel caps, Brand new in packet, to suit doubles
£SOLD

http://i995.photobucket.com/albums/af79/smith9051/28102012842.jpg

Piper valve stem oil seals to suit double springs, Brand new in packet

£SOLD

http://i995.photobucket.com/albums/af79/smith9051/28102012841.jpg


Turbosport round tooth vernier pulleys.

£SOLD

http://i995.photobucket.com/albums/af79/smith9051/28102012827.jpg

Unknown double valve springs, Supplied by Autosprint

£SOLD

http://i995.photobucket.com/albums/af79/smith9051/28102012828.jpg

Unknown multi layer steel gasket. New and unused. 2 of the rivets missing, but they will all need removing anyway.

£15

http://i995.photobucket.com/albums/af79/smith9051/28102012832.jpg

All parts can be posted worldwide at extra cost apart from the block, and collection from Salisbury, South Wiltshire can be arranged.

Paypal preffered,

Craig 07557118213

[8valve-craig]

Have 1 early Coscast head left which might as well go up for sale

This one is a 1989 dizzy head. medium corrosion on the waterways but not near the firing ring, and a small step. Looks to have had a skim or 2 in its time. No valvetrain fitted,

Cams removed but caps all present. SOLD

http://i995.photobucket.com/albums/af79/smith9051/Photo0012-1.jpg

http://i995.photobucket.com/albums/af79/smith9051/Photo0032.jpg

http://i995.photobucket.com/albums/af79/smith9051/Photo0041.jpg

Standard with no modifications

Can post within the mainland for £10

Craig 07557118213

[8valve-craig]

For sale is a complete setup here to run twin carbs on any fwd 20xe.

Still fitted to the vehicle so can be seen working if required, and with no issues so pretty much ready to bolt on and go.

Recently set-up on the rolling road for my engine, but i would reccomend getting them done again when fitted to yours

Sale to include...

Twin 45 dellorto "universal performance" carbs with 36mm chokes
Jenvey 7deg inlet manifold
Twin cable linkage
Cable setup to suit a Nova, right back to the pedal
H+H cavalier mk2 distributor setup, covered around 2000 miles since full rebuild
Ignition leads, coil and amplifier
Facet redtop fuel pump
Malplassi Filter King fuel pressure regulater

Obviously putting this kit together would cost a small fortune so the price isnt really negotiable. The carbs are on nearly new misab plates and thackery washers and made 173bhp and around 150lbft on an otherwise standard xe.

SOLD

http://i995.photobucket.com/albums/af79/smith9051/Nova%20on%20bike%20carbs/nova.jpg

http://i995.photobucket.com/albums/af79/smith9051/Nova%20on%20bike%20carbs/Photo032.jpg

Can be posted worldwide at extra cost, and collection from Salisbury, South Wiltshire can be arranged.

Paypal preffered,

Craig 07557118213

[8valve-craig]

Removed these from my track car this week and cant see me re-fitting them so here they are up for sale.

Currently base mounted to Nova frames, using universal sliders, so a direct fit to any Nova, but can of course be fitted to anything with a little fab.

Both in really good nick, one has a cigarette burn behind the left shoulder, but other than that they are pretty mint.

Sparco inflatable cusion not included, as i need that for my poor old back

£220, Collection only from Salisbury, South Wiltshire.

Better pics available upon request

Craig 07557118213

http://i995.photobucket.com/albums/af79/smith9051/Nova%20on%20bike%20carbs/26102012800.jpg

[reecegsi]

Pm'd

[8valve-craig]

List updated

[8valve-craig]

Still available

[8valve-craig]

Still available

[8valve-craig]

Still available.

[8valve-craig]

Got an XE stripped down yesterday evening. Nearly all parts are available but if its not on the list, or not in the picture just ask as i have left the short engine built up for the time being.

Coscast head is already SOLD

Sump £25
Crank £20
POT fly-wheel £20
Very good LUK clutch and pressure plate £20
Twin V pulley £15
Oil pump £15
Complete oil cooler setup £50
Pickup pipe £5
Oil level sensor £10
Calibra mini loom (start charge) £15
ICV knock loom £5
ICV with pipework £10
Bottom pulley & bolt SOLD
V-drive early P/S pump with bracket £30
Rods £20
86mm Pistons £10 each
Block £25
Dipstick / breather £10
Starter motor £15
Rear water bar £10
3way rubber hose £5
Round tooth cam pulleys SOLD
Cams £20
Standard leads £10
Cam cover in very good condition, no corrosion SOLD
V drive alternator £20
Adjustable alt bracket with bolt and bushes £15
x3 cambelt cover bolts, with rubbers SOLD
SFI box £5
x4 SFI Bolts £5
Inlet manifold £15
Cream injectors £20
Fuel rail and 3bar reg £15
Tb with TPS £15
Nearly mint Dizzy Loom (CTS plug need's mending) £45
GY ECU £15
Early 6pin AFM with bung fitted, not messed with SOLD
Anything else just ask.

http://i995.photobucket.com/albums/af79/smith9051/31102012865.jpg

All prices are Plus P+P. Paypal or cash on collection only.
Craig 07557118213

[8valve-craig]

All parts listed above still available

[8valve-craig]

post deleted

[8valve-craig]

post deleted

[8valve-craig]

post deleted

[8valve-craig]

Verniers and Autosprint springs now SOLD

[baggott]

im very intrested in the ported head mate do you still have this thanks ben

[nova_stee]

Would you sell the 1.8 block? pm me a price posted please

[8valve-craig]

im very intrested in the ported head mate do you still have this thanks ben

Yes i do, Not that the thread makes any sence any more.

Looks like someone went on a big power trip and merged all of my COMPLETELY DIFFERENT threads.

PM me for details

[baggott]

its me whos texting you now from walsall mate

[Stuart]

Yes i do, Not that the thread makes any sence any more.

Looks like someone went on a big power trip and merged all of my COMPLETELY DIFFERENT threads.

PM me for details


That'll teach you to not bump many threads at once....rules are rules, get over it.


For a refresher read here..

http://www.pngclub.com/forum/content.php?24-Novatrader-Rules

[8valve-craig]

Are you serious? 3 or 4 threads all with completely different content? Why on earth would somebody looking for bucket seats enter a thread titled "Xe tuning bits"? And likewise how the hell am i supposed to start a thread titled "XE tuning bits, wossners, cams, springs etc, complete XE breaking, Sparco bucket seats and complete twin 45 / dizzy setup"

You reckon that would fit in the title bar clever clogs?

Maybe i do need to freshen up on your many amazing rules, But as i said via PM to jack there is such a thing as a moderators discretion, which would be a lot more helpful and educational than whats happened here.

I could have even sorted them out myself if it wasnt for someone flexing their internet muscles.

Here you go Stuart I have a job for you which will make you feel important.

Close all of my for sale threads.

[Stuart]

Nahhh, that'll make you happy.

Put it this way, you have a few threads on the go, that's fine.... But a multi bump in one day, now that's taking the piss really isn't it ;) once you calm down from being on a really high horsey you will see sense. Just think how annoying it would be if someone else did the same and your stuff got knocked off the edge of the world.

[8valve-craig]

I agree the boards are small on here, and in hindsight maybe you are right, staggering them is a better idea.

And what a great way of explaining it that was. I understood, and came around to your way of thinking right away, Just like i would have if the very same message had been PM'd to me, instead of someone wading on in and making an even bigger mess.

[8valve-craig]

Carbs & Dizzy kit now SOLD

Both Coscast heads now SOLD

[kellynovaaaa]

are the bucket seats with frames still available?