For sale, braided line (full car) swirl pot, pumps and filter

[t45_ste]

Hi

Im selling a few bits that are no longer needed.

New, unused 1L Alumium swirl pot for use with -6 fittings and -8 supply £70 delivered

New, unused sytec filter ideal for use as pre high pressure pump filter £12 delivered

Cheers for looking

Ste

[novait]

Any pics of the fuel parts??? How much would you do the lot for? Thanx

[t45_ste]

http://i227.photobucket.com/albums/dd315/ste_ed/Image029.jpg

This is the only photo I have at the minute, the lift pump isn't on there and the red and blue filter, lines and fittings are not for sale (although I may have a few fittings knocking about I could sell)

Ste

[t45_ste]

novait, whats your email address, will get some photos to you.

[t45_ste]

Bump

[paul080803]

What comes in a facet redtop fuel pump kit?

[t45_ste]

http://www.rallynuts.com/user/products/large/Silver_Top_Comp_600.jpghttp://www.ebay.co.uk/itm/Facet-Red-Top-Fuel-Pump-Kit-/270875101287?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item3f116a0867http://www.ebay.co.uk/itm/Facet-Red-Top-Fuel-Pump-Kit-/270875101287?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item3f116a0867

[t45_ste]

ttt

[t45_ste]

bumpy

[t45_ste]

up

[t45_ste]

ttt

[t45_ste]

up

[t45_ste]

Ttt

[t45_ste]

open to offers

[t45_ste]

http://i227.photobucket.com/albums/dd315/ste_ed/2ece94a3.jpg

http://i227.photobucket.com/albums/dd315/ste_ed/103cd398.jpg

http://i227.photobucket.com/albums/dd315/ste_ed/af3e0f6b.jpg

http://i227.photobucket.com/albums/dd315/ste_ed/8758c123.jpg

[t45_ste]

Up

[paul080803]

Will the brake lines connect to 256mm front calipers and standard nova rear drums? Are they then 1 fitment for the front and rear to connect onto a nova bias pedal box with twin cylinders?

If so then I will make you an offer on the lines and facet red top fuel pump

[t45_ste]

The lines do not go directly to the calipers/drums, they replace all the solid lines in the car. Also the are for a corsa but by changing a couple of lines around im sure they will fit a nova.

Heres a photo of how the rears connect

http://www.corsasport.co.uk/carimages/1368/07082007013.jpg

http://www.corsasport.co.uk/carimages/1368/07082007014.jpg

[paul080803]

Do they include the bits to go from inside to outside? Bulkhead fittings I think they are called?

What does swapping lines around mean, do I need more parts?

I am not really up on braided brake lines do apologise for all the questions!

[t45_ste]

Ask as many questions as you like and i will do my best to answer.

Yes there are 2 bulkhead fittings. One that goes under the bonnet through into the cabbin and one that exits where the rear bench is (as per photos).

In short, you have an outlet from 1 of your master cylinders to a t piece that splits a line to each front caliper (your flexi hoses then fit to these)

There is another line that goes from the other cylinder, to a bulkhead fitting into the cabin. This line then runs down the centre of the car to a T piece bulkhead fitting. This then splits to each drum flexi.

The two line that would need swapping are those that go from the front T piece to each flexi. This is because of the different position of the nova master cylinder.

Although a good mod to do is to install the corsa bias box and pedal into the same position in the nova. This saves a bit of weight as you can get rid of the balance bar. Some say you get a better pedal feel as well.

[paul080803]

That explained it well, thanks. I dont want to go down the corsa pedal box route.

Can you measure the length of each hose please.

[t45_ste]

Will get some measurements up tomorrow for you :)

[t45_ste]

Here are some measurments for you:

Cylinder to t-piece for front brakes- 52cm

Cylinder to bulkhead for rear - 43cm

T-piece to left hand caliper - 95cm

T-piece to right hand caliper - 145cm

Bulkhead to rear t-piec - 178cm

Left hand rear - 107cm

Right hand rear - 101cm

If you need anymore info let me know.

[paul080803]

Thanks, I am working away at the moment but home at weekend so can measure up. I presume the 4 lines from the 2 t prices to the wheels are not handed so I could swap them around if they fit better?

[t45_ste]

That's correct, even the fittings are easy to swap if the angle is not quite right. I will give you first dibs on them, I have a lad on mig who wants them but you enquired first. just let me know either way.

[paul080803]

Thanks, I will let you know by Saturday eve if I want them or not. Cheers

[t45_ste]

Only swirl pot and filter left

[t45_ste]

ttt

[t45_ste]

ttt

[paul080803]

Good seller guys, parts arrived as described!!

[heds]

is the full setup for sale now? lines/filter/pump/tank?

[t45_ste]

ttt