View Full Version : XE won't start
The 1st and 4th port spark but the 2nd and 3rd don't.
What could be the reason's for this?
Car is a Nova with a XE from the Astra GTE (20XE)
The 1st and 4th port spark but the 2nd and 3rd don't.
What could be the reason's for this?
Car is a Nova with a XE from the Astra GTE (20XE)
Could be duff dissy, leads, rotor arm, dissy cap. got mto be one of them.
w_wall_2001
23-11-10, 10:08 PM
my moneys with rotor arm or dizzy cap, more than likely the dizzy where the points will have burned out inside seeing as only getting spark to 2 plugs
Right OK well i've replaced,
Dizzy cap,
Rotor arm,
Ht leads,
Swapped the dizzy for another,
General Baxter
23-11-10, 10:27 PM
are you sure its lack of spark?
if your getting spark on 1 and 4 theres nothing stopping 2 and 3 from going
erm how are you say this
1234 or 1324 ?
Pistol Pete
23-11-10, 10:28 PM
IIRC firing order on an XE is 1,3,4,2.
General Baxter
23-11-10, 10:29 PM
i know what i mean lol
Pistol Pete
23-11-10, 10:30 PM
lol ok then...
Sorry i meant 1 from being far left and 4 being far right. Ive used an independant spark plug to test the spark also.
w_wall_2001
23-11-10, 10:32 PM
coil? maybe a long shot
General Baxter
23-11-10, 10:35 PM
fault code?
Fault code - low voltage, hall sensor. - ECU light wasn't on but would always show the code if flashed?
I've ran a wire straight from the hall sensor plug to the ECU and still nothing.
General Baxter
23-11-10, 10:41 PM
if i wernt moving this weekend i would pop up your only 20mins away lol
w_wall_2001
23-11-10, 10:42 PM
when you tried the dizzy did it read the hall sensor code still?
if i wernt moving this weekend i would pop up your only 20mins away lol
lol It's OK mate :thumb:
Gunny was stunned by this, he put it down to a wiring problem but i've ran a length of cable and still nothing :(
when you tried the dizzy did it read the hall sensor code still?
I originally had a knackered dizzy on it with the ECU light on showing that code with a lumpy idle also. I changed it for a known working one, the ECU light went out but also shown that code when flashed and the lumpy idle went.
w_wall_2001
24-11-10, 07:30 PM
i may be miles off the mark here but have you checked all the earths on the loom like next to fuel rail as that could trigger low voltages etc
i may be miles off the mark here but have you checked all the earths on the loom like next to fuel rail as that could trigger low voltages etc
The earth's were the first to check mate.
Hall sensor wont stop it firing - I had mine unplugged for a few months without even notcing! lol
I've been thinking .... lol
If the cambelt jumped a couple of teeth, would it cause this problem?
Pistol Pete
25-11-10, 09:57 PM
Well, yeah. Timing would be out!
Well, yeah. Timing would be out!
To cause a spark on the far left and the far right port only?
I still don't know why its not sparking on the middle 2 ports only :(
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.