View Full Version : Dyno run!
Danb1987
19-11-10, 04:58 PM
Got the corsa c20let on the dyno today it ran 220.2bhp and 221ftlbs of torque!
Pretty happy really it's only got an fmic and a dump valve.
I'm having boosting issues atm thow somethings not right when I boot it,, it seems to rev then stop jerk abit pop then go again? Only in the lower gears?
Dan
stupot89
19-11-10, 05:42 PM
good to here mate
what plugs have tyou got in it at the moment
General Baxter
19-11-10, 06:40 PM
its that was n/a that would be a million times better lol
blue_peg_16v
19-11-10, 06:52 PM
sounds like plug gap or plugs tbf
i had the same problem changed the plugs to rs turbo ones and gapes then correctly and its been fine ever since
pictures of slip, of it was a dream!!!!
w_wall_2001
19-11-10, 07:09 PM
a blue peg said, has similar issues myself running super 4's, changes to bcr8es re gapped and never missed a beat since, get a halfords trade card they are less than a fiver for a set :thumb:
sounds like plug gap or plugs tbf
i had the same problem changed the plugs to rs turbo ones and gapes then correctly and its been fine ever since
Danb1987
19-11-10, 07:44 PM
iv got some of them plugs but i need to re-gap them isit 0.6mm they need gapping to?
http://i546.photobucket.com/albums/hh431/danpuntosport/4a1f4f46.jpg
0.7-0.8mm according to haynes
Danb1987
19-11-10, 08:25 PM
Just checked plugs and they are super 4s how do I regap the rs turbo ones without a feeler guage? Isit true use a hacksaw blade? Or shall I just wait till tomorrow lol
Nova_Tek
19-11-10, 08:29 PM
Great result mate, sounds like a healthy LET :thumb:
deanwilko
19-11-10, 08:36 PM
Just checked plugs and they are super 4s how do I regap the rs turbo ones without a feeler guage? Isit true use a hacksaw blade? Or shall I just wait till tomorrow lol
You can borrow my feeler guages if you want im in chesterfield
Danb1987
19-11-10, 08:42 PM
You mean as in I could borrow them tonight? Where in chez are you?
deanwilko
19-11-10, 08:44 PM
brimington
Danb1987
19-11-10, 08:47 PM
Il pm my number mate if I'm alright to nip round? I'm in Heath
w_wall_2001
19-11-10, 08:49 PM
best to use a feeler gauge mate, mine is set to 0.6 and im runnine 1 bar no problem
Danb1987
19-11-10, 08:55 PM
That's good to know matey I thought I'd seem to gap them at that somewhere! Where's the best place to get a turbo to downpipe gasket from other than eBay? I'm wanting to fit a 3"downpipe.
w_wall_2001
19-11-10, 09:22 PM
autovaux, they should have it, all genuine stuff too
Rick Draper
19-11-10, 11:01 PM
Just checked plugs and they are super 4s how do I regap the rs turbo ones without a feeler guage? Isit true use a hacksaw blade? Or shall I just wait till tomorrow lol
Stanley knife blade is spot on.
throw the super 4's in the bin!!!!! dire plugs.
Danb1987
19-11-10, 11:07 PM
changed plugs thanks for the help dean... but it has made no difference what so ever its maybe even worse?? what are my other options/things to check? now its getting to about 3.5k in 4th and holding back?
is it on a dizzy or coilpack?
there is some mod to the dizzy rotorarm to remove the resistor etc on it.
Danb1987
19-11-10, 11:22 PM
Dizzy I think il take a pic of the bay and put it up tomorrow.
w_wall_2001
21-11-10, 08:31 AM
as above dizzy cap or leads?
djbrowney
21-11-10, 09:12 AM
A let never came on coilpack :(
Change your rotor arm and dizzy cap, what condition are your leads in ???
Try a differnt afm from some one else car ect etc
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.