Carbon offcuts

[Mike]

All pieces are genuine 100% real 2x2 carbon fibre twill wet layed by hand, none of the fake tat (plastic sheets coated in twill or lick & stick effect stuffs) all sizes are in mm & all prices include delivery. Gloss finish one side, usual dull/matt finish to rear.

Piece 1 (smallest of the 3)
Dimensions: approx 140x100x0.9*
£ Sold

Piece 2 (medium of the 3)
Dimensions: approx 250x185x1*
£ Sold

Piece 3 (largest of the 3)
Dimensions: approx 370x290x0.7*
£ Sold

Piece 4 (Left overs from today - 19.07.10)
Pulled fresh this morning, however this item is not sqaure at all!
Dimensions: approx 230L x 210W on one side x 190W on opposite side x 195L x0.9*
£ Sold

Piece 5 (Left overs from today - 24/07/10)
Pulled fresh Friday morning. Not sqaure
Dimensions: approx 115L x 85W x 0.7T*
£4.00

Piece 6 (Left overs from today - 24/07/10)
Again pulled Friday morning, also not sqaure.
Dimensions: approx 115L x 115W x 0.7T*
£4.00

Or can do both 5 & 6 for £7 delivered.

(28/07/10) Right got more of this now in all different sizes & shapes from crap ive been making this week.

If you want any, let me know what dimensions your after & ill see if I can match it upto any of the bits Ive got left over & will go from there.

Dont be put off by the cheap prices compared to anywhere else, the reason its cheap is I make it at home for my own & mates project cars/bikes so Ive got next to no overheads at all.

*A note to consider before purchase, the thickness of this matierial. This is single ply carbon sheet offcut NOT suitable for anything structural as its not thick enough (for this you'd require overlayed FG impreg sheet - thicker & a lot stronger) These would be ideal & more suited for ethestically pleasing item's or cut & used as cover's or dash blanks for heater holes etc.

[KSRY]

I'll take the cheapest fella, PM me details

[Mike]

I'll take the cheapest fella, PM me details

As in the smallest piece?? (piece 1)

[KSRY]

Yes Mike

[Mike]

Yes Mike

PM'd you buddy.

[Mike]

up

[KSRY]

Got mine today, thanks Mike!

[Mike]

Got mine today, thanks Mike!

Not a problem matey :)

Dan23, posted yours today aswell :)

[Graeme]

Are you expecting to get any more off cuts Mike? Got a tenner in my paypal to waste if you do

[Mike]

Are you expecting to get any more off cuts Mike? Got a tenner in my paypal to waste if you do

Yes lol ive got shÃ*tloads of the stuff lol only got the one peice for sale at the mo as the rest are for my other car.

Can make these in 0.7 or even overlayed FG for more strenght (1.0 to 1.2mm) will soon be able to make these in pretty much any size squared too.

[Graeme]

I only want a piece to put in a nova clock lol

[Mike]

I only want a piece to put in a nova clock lol

Right, just checked what ive got left over at the mo. Got two pieces of overlayed FG from a panel I completed yesterday (sturdy as fook 1.2mm thickness)

Dimensions are approx 150x70 & the other 285x85

[Mike]

Up

[mk1nova_rich]

i will take the last piece :thumb: PM me your paypal address please :d

[Mike]

Up

[Mazz]

OT i know but, Mike can you make a boot cover panel with the lump for the rear wiper motor?

EDIT, like this

http://i84.photobucket.com/albums/k27/nj_photo/novaturbowip126.jpg

[pie]

have you got any to cover the mk1 center consol?

instead of have 2 compartments :)

[Mike]

OT i know but, Mike can you make a boot cover panel with the lump for the rear wiper motor?

EDIT, like this



Quite possibly, but I'd need to get a OE panel first to take a mould from an go from there. (The OE panel will get wrecked aswell so wont be useable afterwards lol)

If im honest tho, Ive got a bit of a back log of bits Im currently doing so a bit snowed under :( (thankfully its mostly easy stuff!)

[Mike]

Right got more of this now in all different sizes & shapes from crap ive been making this week.

If you want any, let me know what dimensions your after & ill see if I can match it upto any of the bits Ive got left over & will go from there.

Dont be put off by the cheap prices compared to anywhere else, the reason its cheap is I make it at home for my own & mates project cars/bikes so Ive got next to no overheads at all.

[Sloth]

this will sound as bit daft but can you drill or cut a circle into it for a guage?

[Mike]

this will sound as bit daft but can you drill or cut a circle into it for a guage?

Yep. Be aware though carbon fibre "fibres" can be/are as lethal as abestos :( ive got a proper chemical & airbourne particle resistant respirator so I can do stuff like this for you guys if needed.

[Mike]

up

[milko96]

Do you have a piece big enough to cut 2 Nova wing mirror base plates from?

PM me a price if so...

[Mike]

Do you have a piece big enough to cut 2 Nova wing mirror base plates from?

PM me a price if so...

I dont own a Nova :wtf: tell me some measurements an ill let you know.

[Mazz]

Quite possibly, but I'd need to get a OE panel first to take a mould from an go from there. (The OE panel will get wrecked aswell so wont be useable afterwards lol)

If im honest tho, Ive got a bit of a back log of bits Im currently doing so a bit snowed under :( (thankfully its mostly easy stuff!)

I've got an old one you have as a template if you want. I just want a carbon cover that lets me keep the wiper motor as i don't think anyone makes one (gap in the market!)

[Mike]

Ill have to let you know Mazz when Im back from doon saff next weekend. Spending a week working in Conwy in Wales as of 5am Monday :(

[pie]

have you got any to cover the mk1 center consol?

instead of have 2 compartments :)

[Mike]

have you got any to cover the mk1 center consol?

instead of have 2 compartments :)


I dont own a Nova :wtf: tell me some measurements an ill let you know.

:confused:

[pie]

sorry dude my bad :lol:

ya il get some measurements for you :thumb:

[dan23]

do you have any larger off cuts yet