View Full Version : radiator question.
this is what my new rad looks like.
http://i.ebayimg.com/21/!BtwLptg!Wk~$(KGrHqMH-DcEvsKVUrWNBL9T,O7yQQ~~_12.JPG
i am fitting it to my E16se.
I am trying to work out what borrom hose to use......HELP!!!!!!!
what issue you got?
Most likly just need 1.6 gte/gsi hose?
let_nova
05-07-10, 11:29 PM
whats the join in the middle?
mk1nova_rich
05-07-10, 11:29 PM
what issue you got?
Most likly just need 1.6 gte/gsi hose?
the outlet is higher up than on a GTE/GSi
the bottom hose port is about 2" higher than on my original rad, which was from a 1983 1.2 with full height rad & the bottom hose i've been using was a cut n shut i did in 1994, i am trying to do it properly.
whats the join in the middle?
dunno, they all have them
Corsa hose would be good i think.
mk1nova_rich
05-07-10, 11:31 PM
http://www.pngclub.com/forum/showthread.php?t=140464
it looks like a diesel radiator but with the top outlet in a different place
16v Nova Kev
05-07-10, 11:32 PM
gte one.
Corsa hose would be good i think.
off an sri?
Any 4 cylinder corsa imo.
The reason i say is the corsas have the hose about there, and its a preety neat setup.
Only one issue ive thought of, the pipe that runs around the back of your block, is it plastic or metal?
You need a nova gte/gsi/sri hose
Corsa one would be ideal then.
You need a nova gte/gsi/sri hose
The issue is, on a standard nova rad the outlet would be lower, so the pipe ends up being pushed up.
Why is it higher up on that rad,hmmm.
Because its a aftermarket replacement item, so as per normal, is almost nothing like the standard one.
Mine is too, but my hose outlet is in the original position.
Actually, that rads probably meant for a 1.2/1.3, which had a smaller rad as standard,with a different bottom hose. Its just cheaper to just make them using one core size.
Why is it higher up on that rad,hmmm.
i asked for one..and they said it wasn't listed........ typical eh? i think its go down there & rootle thru the books time again
four of them were merrily telling me that i had got square ports on my engine, when i nipped outside & brought the head & manifold in to prove them wrong....considering i'd already told them a e16se was mechanically all but identical to the c16se
Mine is too, but my hose outlet is in the original position.
Actually, that rads probably meant for a 1.2/1.3, which had a smaller rad as standard,with a different bottom hose. Its just cheaper to just make them using one core size.
but i keep reading on here that there were later gsi's with the short rad......
i've just found this for an astra mk3 mpi 1.4/1.6.....
http://i18.ebayimg.com/02/i/000/e4/49/be8c_1.JPG
opinions please. do you think the hose might fit??
Id say so, iirc its the same as corsa too, If i remember, il have a quick look at my tigra in the morning and see if it would work.
mk1nova_rich
06-07-10, 12:13 AM
yeh that looks like it might work, although it might depend on the height of that radiator cos it looks taller than the Nova one you have
i have the rad, its the hose........
and AW06, a corsa b 1.4 8v one is perfect, so rep heading your way.
it ends up is was from a really late gsi..
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.