nova/corsa conversion shafts....

[david dixon]

I am doing a 2nd group buy on nova equal length conversion shafts
These shafts are replaced if they snap.

The price is £142.50 posted for the pair.
For a single it is £74 posted.
I would need at least 5 pair or 10 singles (or somewhere near)
please check page 15 and list below if you are interested but only if you are sure!

** Group buy last page. ** closing date for the group buy is 15/7/10, NOW CLOSED****
Cheers David.

http://img.photobucket.com/albums/v84/nova-turbo/engine%20conversion%20mounts/SHAFTS.jpg

[brucer]

What about equal length for a nova?

[Sloth]

are these for big block hubs? or can youn get the ones for std hubs?

[burgo]

you would sell funk loads if you made some that allowed to keep standard outer

[Sloth]

agreed. 2.0 inners an 1.2-1.6 outers would be mint.

[blue_peg_16v]

no they wouldent there cack thats what courtnay shafts were martin tinker also did them and the splines used to break off in the outter cv as thats the weakest pointt i went through 4 short shafts all broke the same and that was with a standard xe and at that time they would only sell as a pair i still have a couple of long ones in the garage these were all you could get 10 years ago and were 360 a set and were pants hence the emergance of motorsportshafts with big outers

[Sloth]

i'd say thats down to production and design faults. look at gte shafts, small diameter yet used with lets and dont break. i agree a taper doesnt help but if the shaft is the same thickness and made using modern casting techniques it would be fine.

[blue_peg_16v]

the reason gte ones dont break is there able to flex a little as there the same diamiter and is no inherent week point the thicker shafts will not flex at all so the problem magnifies at the weakest point it isnt just me that has had the problem i know 4 otheres that had at least 3 sets of them

if you want nova outers use gte shafts there a safer bet i use them on the loon and there fine and a safer bet imo

the tapered shafts always broke were the outer securing pin sat

[david dixon]

as said tapered are no good at all, i wouldn't even use them on a standard xe!
these are for machined hubs and big block cv's.

David.

[david dixon]

Just so you all know, I could also do equal length in this group buy!

David.

[matthew172]

how much for the equal length shaft?

[Paul]

As above .

[C2VXL]

how much for the equal length shaft?

Same.

[Graeme]

As above

[discoinferno]

equal length are the way forward :D:D:D:D:D

[garethcolley]

Equal length please.

[Benn]

Watching.

[Paul]

Thats 6 of us, gotta be worthwhile cash waiting.

[Nick J]

Thats 6 of us, gotta be worthwhile cash waiting.

Count me in too please for the equal length shaft. (7)

[david dixon]

I could do that at the same price!

If thats 7 then another 3 would do the jb at that price!

David.

[Paul]

I think most of us are after the equal length shaft on its own.

[garethcolley]

I think most of us are after the equal length shaft on its own.

Yeh, i want the single shaft.

[C2VXL]

I'm defo in.

[Graeme]

I'll take the single shaft or the pair, whichever is easier

[david dixon]

I have to be honest the pair would be easier, i will check on the price of just the single shafts

David.

[Paul]

Im not interested in pair, so count me out if thats all you can do.

Paul

[david dixon]

no problem mate

David.

[Benn]

I'm interested in the equal one, but don't need a pair really. So pm me the price too please.

[ben doodar]

I'd also be very interested in a price on just the equal legnth shaft.

[Nick J]

Im after the same David just the equal shaft please. Seems their is a big market for them since chris astley doesnt do them anymore etc.

Nick.

[david dixon]

Ok lads, I can do you the nova equal length shafts on its own for £65 + p&p

Please make a list of your names below.

1.
2.
3.
4.
5.

[brucer]

1. brucer
2.
3.
4.
5.

pm me when you want payment.

[Benn]

1. brucer
2. Benn
3.
4.
5.

Pm me or say when you want the cash,

[Nick J]

1. brucer
2. Benn
3. Nick J
4.
5.

Pm me or say when you want the cash.

[david dixon]

up

[eddgsiturbo]

i would be intrested in the equal length shaft and the otherside shaft is it £130 still? do i still use xe inner and outta cv's on them? cheers

[bazil]

1. brucer
2. Benn
3. Nick J
4. Bazil
5.
6.

Pm me or say when you want the cash.

[david dixon]

any more?

[TWAG]

£65 is a good price! ive done this mod and its well worth it.

[discoinferno]

i 'll have another equal length shaft for spare please

[david dixon]

add your name to the list then please mate

David

[discoinferno]

1. brucer
2. Benn
3. Nick J
4. Bazil
5.Gary (discoinferno)
6.

Pm me or say when you want the cash

[C2VXL]

When does the money need to be in by? I'd be up for this if could pay on payday?

[david dixon]

when is that mate?

David

[Hobbit]

pm'd

[garethcolley]

1. brucer
2. Benn
3. Nick J
4. Bazil
5.Gary (discoinferno)
6. Gareth

[Hobbit]

1. brucer
2. Benn
3. Nick J
4. Bazil
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)

[C2VXL]

Last Thursday of the month. Just bought a new kitchen so kinda skint this month ha ha.

Let me know either way.

Thanks,

Owen.

[david dixon]

i'll see what i can do mate, i'll probably have some left over even if this is complete! give me a shout when you need one.

David.

[garethcolley]

David, when will this be going ahead?

[david dixon]

I need around 10 names mate, soon as i have then its ok to go

David

[haydn_123]

1. brucer
2. Benn
3. Nick J
4. Bazil
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)
8. haydn_123

[BRoadGhost]

1. brucer
2. Benn
3. Nick J
4. Bazil
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)
8. haydn_123
9.BRoadGhost

[C2VXL]

Why is payday always never close enough?

[eddgsiturbo]

is it 130 still for the pair of shafts for a nova with a equal length 1? am intrested if so?

[david dixon]

yes it is mate

David.

[bazil]

1. brucer
2. Benn
3. Nick J
4. Bazil ( full set )
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)
8. haydn_123
9.BRoadGhost



ive added im after a full set,:thumb:

[david dixon]

ok we only need 1 more then i'll have to organise a date for the money

Cheers Lads
David.

[Andy]

1. brucer
2. Benn
3. Nick J
4. Bazil ( full set )
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)
8. haydn_123
9.BRoadGhost
10.The_General_Chancer

My mate Rich- The_General_Chancer on here has just rang me and asked me to put his name down for a full set as he cant get on the net at the moment

[eddgsiturbo]

yes it is mate

David.
shall i just ad my name to the list even though i want a pair includeing a equal length shaft or shall i do it seperate as i want a equal and the otherside? cheers

[david dixon]

just add it on the list saying (full set)

Cheers David.

[david dixon]

1. brucer
2. Benn
3. Nick J
4. Bazil ( full set )
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)
8. haydn_123
9.BRoadGhost
10.The_General_Chancer (full set)

The full sets in this group buy for equal length are £130

Cheers David.

[w88rdy]

david im running standard gte shafts with cav inners on my xe, can you tell me what is the benifit of the equal length shaft please?

[david dixon]

its to try and reduce torque steer and have a more even power spread (helping out the diff)
Also to that they are alot stronger and will be replaced if snapped!

David.

[w88rdy]

so with the new shafts i would run the cvs i already have ?

[Andy]

No thyere for big block inner and outer CV's bud

[w88rdy]

so i would need new outer cvs then to match (sorry for been a pain)lol

[david dixon]

yes and machined inner hubs from a calibra/cav/astra big block for the cv's to fit through

David.

[w88rdy]

ok thanks guys

[eddgsiturbo]

would the hubs from a mk3 astra gsi fit a nova? what part has to be machined? and by how much? do the corsa conversion hubs fit or can u make the hubs? cheers

[Andy]

so i would need new outer cvs then to match (sorry for been a pain)lol
And inners if your running Nova Gte shafts with Cav 1600 inners,as they are 22 spline inner.Conversion shafts or equal length shafts or 25 spline inner so use any f16/f18/f20/f28 inner cv's

[david dixon]

would the hubs from a mk3 astra gsi fit a nova? what part has to be machined? and by how much? do the corsa conversion hubs fit or can u make the hubs? cheers

corsa conversion inner hubs will fit into the nova bearings!

David

[nuds sr]

1. brucer
2. Benn
3. Nick J
4. Bazil ( full set )
5.Gary (discoinferno)
6. Gareth
7.Hobbit (full set)
8. haydn_123
9.BRoadGhost
10.The_General_Chancer (full set)
11.nuds sr (full set)

let me know when the money needs paying
cheers alan

[david dixon]

Ok, people can start paying the money for the shafts any time now, I will set the cut off date at sunday the 25th (5 P.M)
I need all payments to be sent via paypal to g984xrg@yahoo.co.uk, it can be sent as a gift or as a purchase but you will have to pay the fee amount!
When paying please attach a note saying what its for and your full name and address and mobile number (this will be needed for the courier)
Full sets £130 + 12.50 p&p
equal length shaft £65 + £9 p&p (these postage costs are our courier that we use, insured and tracked)

any questions please ask.

Cheers David.

[Benn]

Money will be sent to night.

[brucer]

payment sent for mine, will we have to wait for them all to be made before we receive them?

[david dixon]

yes you will, sorry about that mate

David.

[Benn]

Do you know how long?

[david dixon]

after payment is made it will be 2-3 weeks as they are made on order (cut, splined and heat treated)

David.

[Benn]

Cool cool.

[brucer]

yes you will, sorry about that mate

David.

no worries, the car wont be seeing the engine fitted for a while. lol

[david dixon]

Received payment from;
Mark Hone
Bruce Childs

Cheers David.

[david dixon]

anymore?
payment needed a week today

Cheers David.

[Benn]

Mark Hone is me (my dad) but you should know i hope..lol

[david dixon]

Mark Hone is me (my dad) but you should know i hope..lol

lol I have that covered Benn :thumb:

David.

[nuds sr]

payment sent to you for a pair of equal length shafts
cheers alan

[david dixon]

Received payment from;
Mark Hone (Benn) - single
Bruce Childs - single
Alan (Nuds sr) - pair

Cheers David.

[bazil]

Bazil has paid £142.50

[david dixon]

Received payment from;
Mark Hone (Benn) - single
Bruce Childs - single
Alan (Nuds sr) - pair
Bazil - Pair

Cheers David.

[haydn_123]

Payment sent. Sorry for the delay.;)

[david dixon]

Received payment from;
Mark Hone (Benn) - single
Bruce Childs - single
Alan (Nuds sr) - pair
Bazil - Pair
Hayden Makin - Single

Still awating payment from a few people.

Cheers David.

[Nick J]

Payment sent David.

Thanks,

Nick.

[david dixon]

Received payment from;
Mark Hone (Benn) - single
Bruce Childs - single
Alan (Nuds sr) - pair
Bazil - Pair
Hayden Makin - Single
Nick J - Single

Thanks David.

[david dixon]

up

[david dixon]

A few days left people, there is still people to pay to do the group buy.

Cheers David.

[bazil]

A few days left people, there is still people to pay to do the group buy.

Cheers David.

name and shame mate lol

[Hobbit]

name and shame mate lol

:d paying it now :d

[david dixon]

Received payment from;
Mark Hone (Benn) - single
Bruce Childs - single
Alan (Nuds sr) - pair
Bazil - Pair
Hayden Makin - Single
Nick J - Single
Matthew W (Hobbit) - pair

Cheers David.

[garethcolley]

David, sorry about the delay. Payment sent for one equal length shaft.

Thanks,
Gareth

[david dixon]

Received payment from;

Mark Hone (Benn) - single
Bruce Childs - single
Alan (Nuds sr) - pair
Bazil - Pair
Hayden Makin - Single
Nick J - Single
Matthew W (Hobbit) - pair
Gareth - Single

Cheers David.

[BRoadGhost]

£74 just sent David for a single short shaft thanks

[Hobbit]

Cheers for refunding my payment, didnt realise i paid twice lol top guy :thumb:

[david dixon]

Received payment from;

Mark Hone (Benn) - Single
Bruce Childs - Single
Alan (Nuds sr) - Pair
Bazil - Pair
Hayden Makin - Single
Nick J - Single
Matthew W (Hobbit) - Pair
Gareth - Single
Simon (BRoadGhost) -Single

Cheers David.

[Gareth_C]

I could do that at the same price!

If thats 7 then another 3 would do the jb at that price!

David.

Dont forget me mate or do you need me to text you another 100 times and shout at you from the garden ;) ;) lol

[david dixon]

i'll catch you later on mate

[Count Vaux Alot]

Is there still time to get in on this? im after a pair?

[david dixon]

yes if you can pay sometime tonight mate, payment is being made tomorrow

cheers.

[The_General_Chancer]

hi just sent mine accross now cheers rich

[david dixon]

hi just sent mine accross now cheers rich

pm'd regarding payment.

David

[david dixon]

** Group buy now closed. **
Received payment from;

Mark Hone (Benn) - Single
Bruce Childs - Single
Alan (Nuds sr) - Pair
Bazil - Pair
Hayden Makin - Single
Nick J - Single
Matthew W (Hobbit) - Pair
Gareth - Single
Simon (BRoadGhost) -Single
Gareth C - Single

Shafts will be ordered tomorrow, I will keep you informed through this thread.

Cheers David.

** Group buy now closed. **

[david dixon]

Just a update, shafts have been ordered and payment cleared

p.s We should have some nova and corsa xe/let front engine mounts ready tomorrow.

Cheers david.

[Benn]

How long does it take to make them?

[david dixon]

its 2-3 weeks after payment as they have to be cut, splined and heat treated. they are made to order.

Nova, corsa, tigra seh/xe/let front engine mounts now in stock in the for sale section

David

[Dan Stanley]

Can someone explain what I'd need to run equal length shafts? Ive got an 20XE with F20 box, using 'motorsport' shafts and hubs. My bro has the equal length shafts from a calibra going spare. Can I just use the longer equal length shaft as it is? or is it too long?
:confused: :confused: :roll:

[blue_peg_16v]

you need the centre calibra bit and a shorter outer bit the calibra set up is too wide

[Benn]

its 2-3 weeks after payment as they have to be cut, splined and heat treated. they are made to order.


Sweet.

[Dan Stanley]

Cheers Blue
So was this group buy for the shorter outer bit then?

[david dixon]

this was for the bit connecting to the calibra half shafts and cv's

David

[Dan Stanley]

ok, call me stupid if you want, but just to be clear.......
The part of the equal length calibra shaft that goes from the joint that bolts to the back of the block needs to be shorter in order to fit in a nova? And this was the part you were selling? And lastly is it too late to get one and how much?
My bro ran the whole calibra equal length shaft in his corsa, with just a shorter shaft on the other side of the gearbox. So I suppose corsa B's have a wider track than novas.
:roll:

[david dixon]

yes you right.
corsa does have a wider track.
they have sold but mail me if you need a full set or just a short shaft

David.

[djbrowney]

is it still to late to buy an equal length shaft buddy ???

[badboydc]

how much 4 just the short sharft thanks

[david dixon]

I might be able to sort out another 2 short shafts out for you's
£75 posted if i can.

Cheers David.

[djbrowney]

money sat here waiting buddy

i dont mind if you going to do another set i just want a spare buddy as i already have one !

[BRoadGhost]

Tech question for those running the lay shaft on equal setup:-

What bolt thread / length is needed to mount the bracket to the block [it's two of them]

[bazil]

Any word on a delivery date David?

[david dixon]

i spoke to him friday and he said they are awaiting heat treatment, i will contact him tomorrow to see how long they will be.

Cheers David.

[djbrowney]

did you order extra david ???

[Lee H]

Tech question for those running the lay shaft on equal setup:-

What bolt thread / length is needed to mount the bracket to the block [it's two of them]

I used the same bolts as used on the alternator bottom bracket and engine to block mounts with the 15mm head.

Not much use if you are looking for pitch/length but just noticed no-one else has replied.

[david dixon]

UPDATE;

Just to let you all know, I should have the driveshafts with me by monday evening so all being well you will have them with you some time next week.

Cheers David.

[Benn]

Sweet.

[brucer]

excellent.

[david dixon]

UPDATE;

You should start to recieve your driveshafts during next week, I have all your address here and they are ready to pack.

Cheers David.

[Benn]

Awesome.

[stt]

really annoyed i missed this group buy!

Any idea when you'll be running another?
im after a pair of shafts for a nova equal length setup

[stt]

cna i have first dibs if someone doesnt need theirs!

[david dixon]

they are sent/being sent at the min mate.

If there was enough interest i would do another group buy..... also with hubs if needed.

David.

[stt]

im interested!
I cant use my car without an equal length setup!

[Plug]

im sure i could also get the money together for some if you need numbers bulking up.

Dont need them in the near future but no dout ill want them soon haha

[stt]

how much for hubs?
and is is machined big block flanges to fit standard bearings or
machined nova hubs to accept big block bearings?

[david dixon]

hubs will be around £75 a pair, they are machined to fit nova bearings.
Please start a list for people who are interested in equal length shafts.

David.

[stt]

Put me down for a set of equal length shafts

[david dixon]

Ok just to let the people of the first batch know, the remaining shafts are being picked up in the morning so you should have them by thursday night (latest)

I will start a list of equal length shafts again (2nd batch) please list your name below if you would require a set of shafts or the single equal length shaft!
same price as before.

1. sst
2.
3.
4.
5.

Cheers david.

[Benn]

Got mine to day, looks awesome.

Cheers dude.

[david dixon]

cheers benn,

Glad you happy with how it looks, hope it serves you well

David.

[fastcar1cars]

hi put my name down for equal length shafts and hubs please!!

[david dixon]

1. sst - pair of equals
2. Fastcar1cars - pair of equals
3.
4.
5.

Cheers david.

[Benn]

cheers benn,

Glad you happy with how it looks, hope it serves you well

David.

lol i'll say for sure when its fitted.

[BRoadGhost]

Likewise - received the short shaft this afternoon.

[david dixon]

lol i'll say for sure when its fitted.

I'm sure it'll be fine mate, never had bother from them

David. :thumb:

[Benn]

Awesome.

[brucer]

recieved mine yesterday, thanks for sorting it out david.

[bazil]

Got my shafts yesterday and the look real fine,

the hubs? Will you be doing 4 stud hubs?

[Hobbit]

Mine just turned up, will fit them tomorrow :)

[david dixon]

Got my shafts yesterday and the look real fine,

the hubs? Will you be doing 4 stud hubs?

I can start a second list for hubs below the new shaft group buy if you like

David. :thumb:

[scott.parker]

So am i reading this right, your doing big block equal length shaft (one side) for £75 posted? what do you get for that? just the shaft, or the setup with CV/mount?

Scott

[david dixon]

thats just the shafts mate

David.

[david dixon]

2nd batch of equal length shafts

1. sst - pair of equals
2. Fastcar1cars - pair of equals
3.
4.
5.


Please add your name to this list if you would like a pair of motorsport hubs

1.
2.
3.
4.
5.

Cheers david.

[Nick J]

Shaft recieved David, many thanks. :)

Nick.

[fastcar1cars]

ttt
people get ur names down! I need some shafts man! Lol!

[lomas]

2nd batch of equal length shafts

1. sst - pair of equals
2. Fastcar1cars - pair of equals
3. lomas - pair of equals
4.
5.


Please add your name to this list if you would like a pair of motorsport hubs

1.
2.
3.
4.
5.

[emilyC]

1. sst - pair of equals
2. Fastcar1cars - pair of equals
3. lomas - pair of equals
4.EmilyC pair of equals
5.

[stt]

woohoo! one more person needed!

[pie]

1. sst - pair of equals
2. Fastcar1cars - pair of equals
3. lomas - pair of equals
4. EmilyC pair of equals
5. pie1985 pair of equals

[emilyC]

When will the payment be taken for these? I could do with paying next friday if that isn't a problem?? :D

[david dixon]

Ok then i will set the payment date for next friday(25/6/10) so if anyone else needs any there's plenty of time to add their names.

David.

[emilyC]

Cheers buddy appreciate it! How much would the total be with abd without hubs? :D

[stt]

how do you want payment?

[david dixon]

it will be through paypal mate, contact me if you want to pay now or wait until the date

Cheers David.

[fastcar1cars]

.

[david dixon]

the hubs might also need a few byers but i will check on that too mate

Cheers David.

[djbrowney]

ok :thumb:

[stt]

payment sent for shafts,
how much are your hubs?

[david dixon]

about £75 for the hubs mate

David.

[djbrowney]

have you posted my shafts yet mate :thumb:

[fastcar1cars]

i cant pay till thursday night as this is when i get paid!!!
cheers

[david dixon]

Yes i have mate, if they didn't arrive today then it should be tomorrow.

David.

[djbrowney]

spotty dog buddy

[-JELLY-]

ILL TAKE A PAIR OF EQUAL LENGTH SHAFTS PLEASE MATE :thumb:

[david dixon]

1. sst - pair of equals
2. Fastcar1cars - pair of equals
3. lomas - pair of equals
4. EmilyC pair of equals
5. pie1985 pair of equals
6. -Jelly- pair of equals

if there is anyone else please add to as this will be closed for payment this weekend.

Thanks David.

[fastcar1cars]

hi where am i sendeng payment to? And how much?
Can you pm me please as i wanna send asap as ive been paid! Lol!

[david dixon]

pm'd.
can people that have not paid yet contact me.

Cheers David.

[david dixon]

1. sst - pair of equals - PAID
2. Fastcar1cars - pair of equals
3. lomas - pair of equals - PAID
4. EmilyC pair of equals
5. pie1985 pair of equals
6. -Jelly- pair of equals

Payment due now.

Cheers David.

[stt]

how soon can we expect them?

[djbrowney]

what courier did you post them with ???

[david dixon]

how soon can we expect them?

Its usually 2-3 weks after payment is made.

[david dixon]

what courier did you post them with ???

Dont you have your browney?

David.

[djbrowney]

na mate if its hdnl you used they tried

monday- i wasnt in

wednesday- i waited in all afternoon, the stuck another ticket through the door didnt even ****ing knock

today-left a not saying please leave in the green house

left another note are they ****ing blind or what ???

i rang and compained wednesday and the woman on the end of the phone pretty much said tough **** !!!

stupid slut !!!

[david dixon]

hmmm that doesn't sound right but i'll check it up for you mate, either way not good practice for a courier company of their size!

David.

[djbrowney]

its because im in kings bin mate full of ****ing wasters.

At worst i will go and collect them from norwich on monday when i go to snetertton but thats not the point !

[david dixon]

no its not mate, sorry about the hassle!

David.

[djbrowney]

not your fault buddy

i will just **** them round the head with it, thats gota hurt lol

[david dixon]

not your fault buddy

i will just **** them round the head with it, thats gota hurt lol

Damn right it will lol sounds like a good plan of action to me :thumb:

David.

[fastcar1cars]

Paid!!!

[david dixon]

1. sst - pair of equals - PAID
2. Fastcar1cars - pair of equals - PAID
3. lomas - pair of equals - PAID
4. EmilyC pair of equals
5. pie1985 pair of equals
6. -Jelly- pair of equals

Payment due now.

Cheers David.

[fastcar1cars]

come on people get paying!!
Lol!

[david dixon]

1. sst - pair of equals - PAID
2. Fastcar1cars - pair of equals - PAID
3. lomas - pair of equals - PAID
4. EmilyC pair of equals
5. pie1985 pair of equals
6. -Jelly- pair of equals - PAID

Payment due now.

Cheers David.

[david dixon]

still waiting on 2 payments

David.

[djbrowney]

I didnt have the time to collect monday with being so busy with pauls cars, so i arrange them to deliver yesterday, never even turned up this time !!!

[david dixon]

thats proper shocking mate, i'm please you told me though at least i know never to use those for a courier in future!

David.

[eddgsiturbo]

is it to late to get just the equal length side shaft? cheers

[david dixon]

no its not mate as i am still waiting for people to pay, add your name to the list saying (single shaft) then mail me for payment details.

Cheers David.

[djbrowney]

i phoned hdnl yesterday, they said i had to get in contact with another courier which is part of the company (they tried to deliver 4 times and wouldnt try again) Of which 3 times i didnt ask them too. AFter getting hold of this other courier i asked them to send them to my work shop where somebody would be all day

guess what they never delivered them

so im £130 out of pocket and still no shafts ???

[david dixon]

where are the couriers mate?

David.

[djbrowney]

i dont know who ever you sent them with buddy lol

[david dixon]

no i mean where are they holding them at?

David.

[djbrowney]

norwich branch mate ! but they did say they are only holding them for 5 say before they send them back so **** know where they are now. Btw i always use dhl and havent ever had a problem !

[david dixon]

Well if they come back here in th enext day or 2 i will let you know

David.

[fastcar1cars]

Can everyone who put there name on the group buy get payin as i want my shafts! Lol!!

[stt]

Can everyone who put there name on the group buy get payin as i want my shafts! Lol!!

What he said!!

[fastcar1cars]

david how much more money needs to be collected before the gb can go ahead?
Cheers john

[david dixon]

I need at least another pair mate

David.

[djbrowney]

any news on mine mate ???

[david dixon]

well they haven't turned up here, i'll ring them monday and see where they are.
do you want the shipment number so you can track them?

David.

[djbrowney]

i dont have anything mate, you should have the tracking number buddy

[david dixon]

lol thats what i said, i'll pm your the tracking number so you can see what the crack is too

[fastcar1cars]

1. sst - pair of equals - PAID
2. Fastcar1cars - pair of equals - PAID
3. lomas - pair of equals - PAID
4. EmilyC pair of equals
5. pie1985 pair of equals
6. -Jelly- pair of equals - PAID

Payment due now.

Cheers David.

pie1985 and emilyc why put you name down and not pay?? Come on!!

[fastcar1cars]

Ttt

[david dixon]

we need people to pay here to get this sorted

David.

[fastcar1cars]

david have you pm'ed the remaining people who need to pay??

[david dixon]

yes i have mate, no answer so i am thinking about removing their names shortly

David.

[fastcar1cars]

ok cool mate!! and you say 1 more set and we can go ahead??
1 more person must want a set??

[david dixon]

leave it with me mate

David.

[fastcar1cars]

cool mate it in you hands!! lol!
cheers mate!!

[stt]

any news on the non payers yet?

[david dixon]

No mate, i'm going to have to see if i can find one more!

Cheers David.

[stt]

somebody please buy a set!
I need these to be able to use my car!!!!

[stt]

will you do a discount on a second set if i buy them?

[fastcar1cars]

will you do a discount on a second set if i buy them?

loads rep if you do!! Top man!

[david dixon]

i'll get back to you tomorrow on that, i am just trying to sort it out with what we have

David.

[fastcar1cars]

Any news?
Cheers

[david dixon]

Just to let you know, i have sorted it out to go ahead with the buy with only the amount of people that has paid, he said he will get a start on them probably monday when he swaps the tooling over, i will keep you updated.

1. sst - pair of equals - PAID
2. Fastcar1cars - pair of equals - PAID
3. lomas - pair of equals - PAID
4. -Jelly- pair of equals - PAID

Cheers david.

[fastcar1cars]

Thanks for sortin that out david! I jus wish certain people wouldnt waste mine and your time!
Cheers

[fastcar1cars]

Any updates buddy?
Cheers

[david dixon]

Just an update on the shafts, I have spoken to him today and they have been started so hopefully they will be ready for heat treating monday.

I'll keep you updated.

David.

[david dixon]

Just a update,

The shafts should be ready for the weekend so i should have them to you at the start of next week.

David.

[david dixon]

Update,

The shafts were posted out today so you should have had them today or tomorrow.

Cheers David.

[stt]

thanks, i'll keep my eyes open for the courier then!

[stt]

Mine arrived today, Thanks

[lomas]

got mine the day, seem better quality than lmf ones, will let you know next summer

[david dixon]

pleased you got them lads

David.

[fastcar1cars]

still not got mine mate! When do u rekon ill get um?
Cheers

[david dixon]

hello mate,

If yours hasn't turned up today it'll be monday, not sure why its not there today though.

David.

[fastcar1cars]

ok mate hopefully monday!!
cheers