View Full Version : Where can i buy.......
A stainless 4 branch manifold to fit a 1.3sr ?
Tried looking everywhere and can't find anyone that lists them.
Any ideas ?
Thanks in advance Edd.
dontliftdrift
24-01-10, 02:44 PM
when i had my sr i had an ashley manifold fitted but this was 5 years ago....not sure if they are still making them for the sr?
edit: ashley isnt stainless,sorry!
looked on there site.
mild steel only.
dontliftdrift
24-01-10, 02:47 PM
http://www.pngclub.com/forum/showthread.php?t=137728
this guy has a AAS stainless?
novacabrio
24-01-10, 06:02 PM
http://www.pngclub.com/forum/showthread.php?t=137728
this guy has a AAS stainless?
Won't sell it, I know him and i've asked. AAS will make a new one for £330 :thumb:
AAS will make a new one for £330 :thumb:
keen price, only place of i know of so far that makes them tho.
anyone got any other ideas ?
does it have to be stainless?
dontliftdrift
24-01-10, 06:24 PM
im all outa ideas but ill keep searching :)
magnex used to do one edd, 4-3-1. have stopped making them now, but they occasionally pop up on ebay.
does it have to be stainless?
Yes lol. Janspeed used to do them, think they dont anymore tho :confused:
seen loads of mild steel ones forsale.
if i cant find a stainless, then i will go down that route.
Who is AAS???
Edd you got a local power flow or similar exhaust company, to make one?
novacabrio
24-01-10, 06:28 PM
http://www.aas-exhausts.co.uk/
Based 2mins from me, great guys, they did Geordie Chris's exhaust
Edd you got a local power flow or similar exhaust company, to make one?
would meen trailoring the sr there, and the Powerflow near me is shocking quality to say the least.
craig green
24-01-10, 06:54 PM
Get BTB, Primary Designs or Simpson to make one. With the supercharger you will want larger primaries than anything used for N/A anyway.
I got quoted £650 for a custom built manifold in stainless a few weeks ago. I bet Simpson arent far off that!
novacabrio
24-01-10, 07:30 PM
I cant reccomend AAS enough, excellent value and they know what they are talkign about, not expensive as they havent got the name yet, couple of guys turned a hoby into a business
Novasport
24-01-10, 08:13 PM
Lexmaul used to do them but not anymore. They do them for the GTE but not sure if they fit plus if it did you will have a boss to run an oxygen sensor if you need it or just block it off. Not the best looking stainless manifold but stainless all the same.
Can you not just get a mild steel manifold Cermakromed?
Can you not just get a mild steel manifold Cermakromed?
Whats the finish like on this Rich?
Whats the finish like on this Rich?
was thinking this also and where to get it done.
Novasport
24-01-10, 11:11 PM
Quite good afaik, picked up some leaflets at the Classic Car show last year but dont know what I have done with them.
Try here...
http://www.camcoat.u-net.com/Exhausts.htm
Quite good afaik, picked up some leaflets at the Classic Car show last year but dont know what I have done with them.
Try here...
http://www.camcoat.u-net.com/Exhausts.htm
Cheers Rich this is the kind of thing im hoping to do with the sport.
AAS Top quality work from these guys. You'll do well to find better IMO. :thumb:
Avoid any Powerflow at all costs! lol
Top quality work from these guys. You'll do well to find better IMO. :thumb:
Avoid any Powerflow at all costs! lol
Depends on who owns the powerflow joint, gareth at welsh coast customs is a powerflow dealer I believe, and his stuff is top notch.
I didn't know WCC was Powerflow, in that case I take it back - one is very good.
Shame most of the franchises are dog sh!t and ran by clueless muppets!
GRUNT 16V
25-01-10, 01:13 PM
Leave This With Me I May Have One In The Shed !!! I Am Being Serious!!!!!!
Leave This With Me I May Have One In The Shed !!! I Am Being Serious!!!!!!
best you have a look and get back to me then lol
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.