View Full Version : Transducer Help for Digi Dash
morpheus
24-03-03, 03:20 PM
Hi,
I have a 8v digi dash with alll the loom but no transducer.
I rang Vauxhall to buy one but there is 3?
1) ?34 - 16 Impulse
2) ?57 - 16 Impulse
3) ?76 - 8 Impulse
Now guessing i would say the 8 impulse but its very expensive!!!!
But can I get away with any if it being fitted into a Nova?????? :twisted:
YOU WONT BE BUYIN FROM VAUX!! No point mate! You can a whole MINT digidash and trans for ?50 inc delivery normally! Look in the for same section or visit some scrappies and pray!
Aragorn
24-03-03, 09:12 PM
ok heres what u do
goto your local scrappy
find a 1.2 SPi nova
rip the gearbox sender off keeping some wiring loom
pay a few quid for it or put it in your pocket
attach it to your gearbox and wire in like normal
and if everything works u'll have a working dash - mite need to flick that wee switch on the top
morpheus
25-03-03, 10:09 AM
How will a 1.2 Nova transducer work???? and whats a 1.2 SPi????
mikeoxford
25-03-03, 11:00 AM
How will a 1.2 Nova transducer work???? and whats a 1.2 SPi????
you need a 1.2i - meaning INJECTION sensor
between the mechanical drive and the gearbox on the single point injection (SPI) novas, there is a similar transducer
it only works with 8v digidashes though.
morpheus
25-03-03, 01:51 PM
dont suppose you know where i can get one from???
Ill pay good money for it???
Aragorn
25-03-03, 02:02 PM
just go to your local breakers, find a mk2 1.2i or 1.4i and whup the sender off the box
if u send me "good money" i'll do the same ;) but thats totally pointless as u can just goto a breakers yourself
unless,, u have a 1.2i nova? in which case u already have the sender :D
morpheus
25-03-03, 02:26 PM
Sender, isnt it connected to the gearbox as I need to know what im asking for off the 1.2i, 1.4i as I have a GSi and really as you can tell am quite clueless about these things??
So what should I ask for, off the gearbox?? to make my 8v digi dash work??
Aragorn
25-03-03, 02:31 PM
if its the multec GSi u already have it
if its a bosch GSi u dont
have a look and see
morpheus
25-03-03, 02:41 PM
How do I tell?? Where do I look and if it is multec how do I rig up the digi dash???? I have a wiring guide for the Astra GTE transducer is it the same????
Its a K plate GSi if that helps????/
Sorry, Im a novice????
Aragorn
25-03-03, 03:08 PM
ok the multec GSi has no AFM
if u look under the bonnet u see the air pelnum at the back of the einge with the black air pipe coming off
this should go streight to the airfilter if uve got a multec car
if its a bosch car it will goto a silver "bosch" box which the airfilter is attached to
got a photo of the engine bay?
morpheus
25-03-03, 03:15 PM
Yes I have a pic, whats you email address?[/img]
morpheus
25-03-03, 03:20 PM
the air filter is a black box with GM on it if that helps??
TaiTers
28-03-03, 08:01 PM
Ive just got another digidash (one that works with loom for ?5 from scrappy today) its a 16v one but I have a Nova 1.2i Luxe Plus, I have the 3 cables coming off the transducer currently there, Ive hooked the wire up to the dash and it works fine, just doesnt read the right speed, its way too low less than half as fast.
Is there a switch on my dash that would sort this?
If not I do have the Astra GTE transducer but how do I get my one off its soo hard to get too.
Thanks for any help.
mikeoxford
30-03-03, 08:43 PM
try flicking the red switch on the top of the digi dash - usually sorts it
Aragorn
30-03-03, 10:50 PM
naa it wont
u have a 6 impulse sender (SPi) which will only run an 8v digidash
the 16v dashes use 16 impulse senders - so u need to get one :(
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.