Jamacian Yellow XE

[Andy]

what size is the box please john?
and how much was the kit,pm if you prefer.
Im just weighing up making one vs buying one.

[DAFTJOHN]

Bushes arrived

http://i564.photobucket.com/albums/ss86/DAFTJOHN/C074E728-211B-40CA-847E-09240EC96E74-1291-000000AF22DC957E.jpg

[DaftJohns_Mate]

Weet Weel!

[DAFTJOHN]

what size is the box please john?
and how much was the kit,pm if you prefer.
Im just weighing up making one vs buying one.

It was 175 delivered ill measure the section when I'm home

Cheers

[Andy]

Thanks mate did you have to weld it up your self?

[DAFTJOHN]

Thanks mate did you have to weld it up your self?


Nope, comes in two a frames, 4 poles for stabilisers and then the two mounts to the car thAt allow the pivot.

I'm gonna have casters welded and the stabilisers welded in place.

[Andy]

Thanks again.

[L14MNP]

Are we talking about a roll-over jig/spit? I bought mine for 120, tailored to the car. Piece of piss to weld up.

[DAFTJOHN]

Are we talking about a roll-over jig/spit? I bought mine for 120, tailored to the car. Piece of piss to weld up.

Yeah, this was all built up delivered to the door.

[DAFTJOHN]

what size is the box please john?
and how much was the kit,pm if you prefer.
Im just weighing up making one vs buying one.

40mm x 40mm and 3mm thick steel

[scott.parker]

Just seen them on his site, seams a dam good price delivered as I doubt I could buy an make it for much less then £100

[EwanG]

Just seen them on his site, seams a dam good price delivered as I doubt I could buy an make it for much less then £100
Its probably about £60 tops for the steel. But also time to make it plus welding wire and gas. So the price aint too bad with the next day delivery. I should start making these as I work in a fab shop :d.

[Andy]

Its probably about £60 tops for the steel. But also time to make it plus welding wire and gas. So the price aint too bad with the next day delivery. I should start making these as I work in a fab shop :d.
I dont work in a fab shop but i could make them for what you say aswell,£5 worth of wire,£5 of gas,if not less.

[scott.parker]

Its probably about £60 tops for the steel. But also time to make it plus welding wire and gas. So the price aint too bad with the next day delivery. I should start making these as I work in a fab shop :d.

Do it ill have one from you for £100 delivery.!

[DAFTJOHN]

Exhaust heat warp here

http://i564.photobucket.com/albums/ss86/DAFTJOHN/6EDDB711-6142-4A7F-A536-53259403D4F2-2550-00000184AA4CABAD.jpg

[DAFTJOHN]

Dirty front struts and rack
http://i564.photobucket.com/albums/ss86/DAFTJOHN/827FED44-4F1B-410B-A45F-7EDDEEA133D9-153-0000000760178710.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/DFE3E30D-71FA-4273-A513-323058A02BD0-153-0000000766DB2090.jpg

Back panel
http://i564.photobucket.com/albums/ss86/DAFTJOHN/EC21E5E1-56B8-4F28-9979-44CEC1140A6D-153-0000000773EAF499.jpg

Rust on drivers side, that's about all there is
http://i564.photobucket.com/albums/ss86/DAFTJOHN/5063CAD9-4E79-42A5-82E9-B70BB04CD630-153-000000076D4CBE4B.jpg

Underside - will be all taken back to metal, cavity waxed, undersealed then painted jam yellow
http://i564.photobucket.com/albums/ss86/DAFTJOHN/8D29B2FD-209E-457B-AC77-F481D1F06B55-153-000000077A267685.jpg

[DAFTJOHN]

We inner wing shot before rub down. It's solid.
http://i564.photobucket.com/albums/ss86/DAFTJOHN/1AD31CD2-A164-4A74-A726-CD295EC87AA2-431-00000025293CC61E.jpg

On the jig and back in the garage. I need a double garage with higher roof!
http://i564.photobucket.com/albums/ss86/DAFTJOHN/52F9E471-3D79-428D-895B-4B4C5D4DBCFC-431-000000251F5F9726.jpg

On the whole very very happy with the rear chassis legs, floor and under tank. Few wee flakes on the sill and front inner wings that need sorted but hey it's a nova

[scott.parker]

Can you fit the nova in the garage on its side attached to the jig?

[vx kev]

When you spin it over John how close is the roof to the Deck and how easily does it spin?
Thinking about getting one of thee Jigs as it looks much easier to get a proper job done on the underside.

[scott.parker]

Lol as kev says I'm close to ordering one just want to make sure I can use it..

[DAFTJOHN]

Can you fit the nova in the garage on its side attached to the jig?

It won't fit in sideways but I've a door motor bolted to the roof the looses over a foot.
It fits fine when turned 180.

[DAFTJOHN]

When you spin it over John how close is the roof to the Deck and how easily does it spin?
Thinking about getting one of thee Jigs as it looks much easier to get a proper job done on the underside.

It spins with one finger, there's about 4 inch from roof too floor. My garage is on a slope and it went over the lip fine.

[DaftJohns_Mate]

Piece of piss once you get the right hole! ;)

[NOV4_SPORT]

Looking good John mate, was good catching up with you the other day and will pop over at the weekend for a little look at the shell

Iain

[scott.parker]

It won't fit in sideways but I've a door motor bolted to the roof the looses over a foot.
It fits fine when turned 180.

So if you had a standard door no motor you think it would be alight?
As I do want to buy one then find I can use it on its side in a standard garage lol

[DAFTJOHN]

So if you had a standard door no motor you think it would be alight?
As I do want to buy one then find I can use it on its side in a standard garage lol
What's the internal height of your garage and ill see if it will fit.

[sport]

John did the new painter guy come and look at the shell?

[DAFTJOHN]

Right o, the cars ready to have some welding. Ideally I think it needs a front panel and I'm not happy with the bottom of the sills. There is a little rot around the drivers rear inner wing and the hole where the overflow pipe goes.
http://i564.photobucket.com/albums/ss86/DAFTJOHN/30CEBE9B-3DFF-444A-8065-CC359121C0A3-4201-0000022A15306FA6.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/C4BFC44C-F526-45DA-9492-1BA88144DE24-4201-0000022A1E3EA226.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/9D72F635-932F-41E3-8CA1-460C812487AD-4201-0000022A273B3959.jpg

Behind the tank and chassis legs are sound
http://i564.photobucket.com/albums/ss86/DAFTJOHN/B9E21ED0-6BC8-4147-A6D2-C99AD12F8068-4201-0000022A2E6BF9D5.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/2E518698-4AB0-4F6B-8561-FE3014288905-4201-0000022A3622F711.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/797B2BB3-A300-4413-886C-5BB86308D491-4201-0000022A3F8DB0E7.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/8550FA75-9BE3-48DE-A8E1-059705BC1116-4201-0000022A47E24D25.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/D95ED0D5-2481-41B6-AF62-2FC424730D68-4201-0000022A514BE9A9.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/0D6675FD-7A0B-4F69-9035-9D8ACC6B2033-4201-0000022A57E07570.jpg

[DAFTJOHN]

John did the new painter guy come and look at the shell?

He did mate, he's quoted me to build the door, tailgate up, polish, vinyl on and windows in. Good quote. The more I'm going around the car the more little bits I notice so while its like this it'll be getting sorted. Prob have the lower half repainted.

[sport]

Good good mate shame the bits werent caught earlier on.

[DAFTJOHN]

Good good mate shame the bits werent caught earlier on.

I've got a bit of OCD when it comes to this car lol. Ill keep on a roll and have it ready for next year :)

[sport]

Be nice to see it back out John.

[Benn]

Nice clean chassis legs.

[DAFTJOHN]

Nice clean chassis legs.

Yep really happy with them. Especially for a 84 car

[bazil]

Poor nova lying on its back, naked with its legs in the air:eek:

Looks good though John :thumb: I'd be well happy with its condition,

[DAFTJOHN]

Poor nova lying on its back, naked with its legs in the air:eek:

Looks good though John :thumb: I'd be well happy with its condition,


Ouch, better keep those wee fiestas out the garage...can't have the nova getting humped!

[DAFTJOHN]

Sandblaster booked in for next weekend to strip back the underside. Can't wait to get this finished now....

[DAFTJOHN]

Ready for sandblasting next weekend. Most of the sealer off
http://i564.photobucket.com/albums/ss86/DAFTJOHN/0DA53291-F1EA-4E35-871B-9948C9A2947A-2898-000001D7224D699A.jpg

Powder coated parts and polly bushes
http://i564.photobucket.com/albums/ss86/DAFTJOHN/A9B5A185-2445-4E6D-821C-9F247C2EB376-2898-000001D78A66E2F7.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/6E0CC6EC-DB4D-42CD-BE78-3B8C3677B2DB-2898-000001D7910AC167.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/CE4FFACF-1BBA-41D4-B4A6-422C604BCAC3-2898-000001D79811A717.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/FE9711E9-CDFA-4224-B7F1-CDEA2DEFD187-2898-000001D79EB02432.jpg

Painted box
http://i564.photobucket.com/albums/ss86/DAFTJOHN/B80D023B-793B-4E58-B128-3FCB44097B49-2898-000001D7A47AD077.jpg

How the engine looked
http://i564.photobucket.com/albums/ss86/DAFTJOHN/2EA4C7B4-700E-457B-A982-40AB9F385117-2898-000001D7CB227A31.jpg

And now

http://i564.photobucket.com/albums/ss86/DAFTJOHN/4435ED1B-7A11-4E4C-B100-FA69C88B802A-2898-000001D7A95BE571.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/350D4338-A892-4B54-BE8F-B676836C4F6C-2898-000001D7AE2AA289.jpg

[DaftJohns_Mate]

looking awesome!!

[Nick J]

I'm pretty sure sandblasting the underside is not something I would consider now everything above it has been freshly painted!! Believe me when I say it gets everywhere even when using the smaller portable units so I'd be very careful if I were you! my chosen method would be strip it by hand as you have been doing just to be safe.

Nick.

[scorge01]

Awesome loving the shiney parts :)

[DAFTJOHN]

I'm pretty sure sandblasting the underside is not something I would consider now everything above it has been freshly painted!! Believe me when I say it gets everywhere even when using the smaller portable units so I'd be very careful if I were you! my chosen method would be strip it by hand as you have been doing just to be safe.

Nick.

Cheers Nick, I've just cleared the garage out and taped all the holes that would let the sand into the interior. The shell will be getting painted again. A new front end is going on and there's some bits needing finished due to me deciding to go the full hog.

[NOV4_SPORT]

Looking good John mate, wish I had come over today for a catch up, parts and the engine looks spot on mate keep it up

Iain

[Nick J]

Cheers Nick, I've just cleared the garage out and taped all the holes that would let the sand into the interior. The shell will be getting painted again. A new front end is going on and there's some bits needing finished due to me deciding to go the full hog.

Ah right thats fair enough I didnt know you were doing all that! will be a belter when its finished in that case!

Nick.

[DAFTJOHN]

Ah right thats fair enough I didnt know you were doing all that! will be a belter when its finished in that case!

Nick.

Hopefully mate, just decided to do it once and get it right. Plan on having it for a long time.

[DAFTJOHN]

Looking good John mate, wish I had come over today for a catch up, parts and the engine looks spot on mate keep it up

Iain

Yep all coming together now. Dreading detailing all the trim and the bolts etc lol

[gary_126]

Looking good!

[DAFTJOHN]

Wheels straightened and coated
http://i564.photobucket.com/albums/ss86/DAFTJOHN/CC9166D4-B26E-4724-8B8C-0B34965275A5-805-000000853444772E.jpg

Fuel tank came up well
http://i564.photobucket.com/albums/ss86/DAFTJOHN/1402D8AD-44AA-42E0-9172-537D948AE13C-805-000000852B8BE2C5.jpg

Engine ready
http://i564.photobucket.com/albums/ss86/DAFTJOHN/90681BA7-2510-4A34-A008-DB8AE641BF4A-805-000000852432AD08.jpg

Shells getting sandblasted next Saturday then welding, new front end then full respray and built up for Feb.

[Balley]

Looking very nice!

[chrisd1986]

Ive just read this whole thread and i cant wait to see the finnished product

[sport]

Sounds like your getting on with it John.

[vx kev]

Tank looks awesome, is that powder coated?

[DAFTJOHN]

Tank looks awesome, is that powder coated?

Yep, it's been powder coated

[paulyb]

What a great read, great work, used to love these when they were new. One of the best colours for a sr:)

Don't know how many times I read "It's in the attic' :D

[NOV4_SPORT]

Mmmmmmmm very nice mate !!

[Benn]

Tanks nice.

[shaunboy84]

where did you get the repair panels mate

[shaunboy84]

this car is amazing , love it mate :)

[vx kev]

Yep, it's been powder coated

Was it a new tank you had done or an old one john?
I always wanted to do this but thought the blasting process may destroy an old Nova tank.

[NathanKirkpatrick]

what colour are the speedlines?

[Steve]

Nice colour on the wheels/tank.

[BRoadGhost]

That grey is correct.

...The sh1t I wouldn't do to a shell on a jig.

[16v Nova Kev]

Make one they ain't Exactly hard

[DAFTJOHN]

Riiiight, the bodywork and paint guy have spent a day with the car and went away and worked out the figures.... Scary £3700 to weld and paint.

Alot of money :(

The jobs consisting of

New front Panel welding in
making the alternator cut out a bit bigger
re-welding the engine bay
welding splash guards
wleding the panel the meets the front panel
weld in new outer sills
dress inner sill where jack has affected it
small weld on floor under seat cross member and re-weld cross member back in
plate inner rear arches
plate rear arch to inner arch (previous job just had them sealed together)
new rear panel
re-seal boot once inner rear arch welded
paint boot floor
flatten and paint doors, boot and bonnet
shell to metal and paint
underside all painted
fit back glass
fit doors tailgate and bonnet
paint and texture bumpers


Bingo - 6 weeks later job done, engine in

[dannymcc]

£3700 is a lot of money but at least you'll know it will be left right when you get it back on the road. :)

[Edd]

Does Sound alot but taking into account of what your having done it's not that bad IMO

Least you'll know it's all good when it's done

[sport]

A lot of cash mate, have you seen any of there previous jobs?

[DAFTJOHN]

A lot of cash mate, have you seen any of there previous jobs?

Yeah seen some cars he's put out. Looks like factory paint. He's still usnh solvent based paints. He's had a few project type cars that have had 20-25k spent on them.

[bazil]

Sounds about right for a proper job mate,

[Steve]

Yep, not a bad price, as long as you can afford it and are happy with their work then game on! :)

[DAFTJOHN]

Off it goes

http://i564.photobucket.com/albums/ss86/DAFTJOHN/B0AFAE49-2751-4B63-A347-3368EA23C1EC-642-0000004C4FEBDD38.jpg

[EwanG]

Good decision John. When you get it back I hope your are happy with the finish. It makes sense to just spend the cash and let someone else do the hard work as it takes the hastle and stress out of the job! I would of done the same lol. Anyway I cant wait to see the car when it is finished. I am jealous as I could only ever dream of owning a jamacian yellow sr. Are you fitting new vinyls or getting the lower half painted?

[EwanG]

I am sure you have seen this photo on my facebook but here it is again..
http://i1155.photobucket.com/albums/p545/Ewannova/yellowsr_zps5d106732.jpg

I know you have wheels but I think you should get the standard 3 spokes and the car will look spot on :thumb:

[DAFTJOHN]

Good decision John. When you get it back I hope your are happy with the finish. It makes sense to just spend the cash and let someone else do the hard work as it takes the hastle and stress out of the job! I would of done the same lol. Anyway I cant wait to see the car when it is finished. I am jealous as I could only ever dream of owning a jamacian yellow sr. Are you fitting new vinyls or getting the lower half painted?

Definately, no space in my garage. These guys have the space and skills lol

Vinyl is going on in all the oe places.

[EwanG]

Definately, no space in my garage. These guys have the space and skills lol

Vinyl is going on in all the oe places.
Yep leave it to the bodyshop and put your feet up lol. Did you get vinyls? There is a genuine set on ebay the noo.

[DAFTJOHN]

Yep leave it to the bodyshop and put your feet up lol. Did you get vinyls? There is a genuine set on ebay the noo.

Off to look! Cheers. Managed to get copies

[DAFTJOHN]

Fuk me! He's wanting 365 without the door pillar vinyl

[EwanG]

Fuk me! He's wanting 365 without the door pillar vinyl
Aye a ken lol. If your happy with what you have then fit them :thumb:. Its priced high cause they are non existent!

[tahir868]

Looking forward to seeing this in the bodyshop and back. Always really liked these :thumb:

[DAFTJOHN]

Aye a ken lol. If your happy with what you have then fit them :thumb:. Its priced high cause they are non existent!

Yeah happy with them. Not sure if ill put the lower half on.

[Andy]

This is going to be one nice car when finished.
Attention to detail is spot on.

[leggattr]

With regards to decals, Iv found all the lowers bar 1 for around 70euro. Made me look twice when I saw the price of them on the bay.

[DAFTJOHN]

Axle done, just bushes needed

http://i564.photobucket.com/albums/ss86/DAFTJOHN/D224794F-E879-481A-B0B2-3B7CFCB62E84-1669-000000EAB5844731.jpg
http://i564.photobucket.com/albums/ss86/DAFTJOHN/9A94A466-3EBE-46F2-9076-7C1B890138F8-1669-000000EABD4E0A6E.jpg

[DaftJohns_Mate]

Metal coatings have turned out really well!

[16v Nova Kev]

Is the guy called Ross that's doing it

[DAFTJOHN]

Is the guy called Ross that's doing it

Nah mate, Ian

[Andy]

Thats nice,very nice finish.

[g111mds]

Making some nice progress on this.

[16v Nova Kev]

This not done yet!!!!!!

[DAFTJOHN]

Not there Kev lol. Went to see it yesterday and its looking worse to look better.

Passenger sill off and all the old metal and cataloy out from the lower arch
http://i564.photobucket.com/albums/ss86/DAFTJOHN/3DEF9278-4CEC-4218-95DB-602127805E38-57135-00000A09C2CCFB74_zps53299199.jpg

Rot cut away from the inner wing where it meets the chassis leg. Inside the leg is mint. Happy with that
http://i564.photobucket.com/albums/ss86/DAFTJOHN/955EF5D7-5A3C-49DA-B0C6-E11EE226A4E1-57135-00000A09A2EAE08E_zpsbc89aa16.jpg

New splash guard section before finishing
http://i564.photobucket.com/albums/ss86/DAFTJOHN/A92AD16A-0015-4E5D-BB07-158EE0DD9321-57135-00000A09BD20C9B5_zps5ff5404a.jpg

****ty bit of metal from previous repair

http://i564.photobucket.com/albums/ss86/DAFTJOHN/E35697DA-F0BB-4FF9-A083-31BD8E76410B-57135-00000A09ADED3820_zps77f7a498.jpg

Think once all the body work is out the way the prep and paint should be done in around 2 weeks. Should be back by end May.

[16v Nova Kev]

That's cool. Mine has ground to a halt can't get near it

[DAFTJOHN]

This will probably be up for sale. I wanted it to look original in the bay, a plates been welded in to take out the xe cutout. But at the same time the body shop ground down the stitch weld and seam welded the inner wing / turrets - which takes away the standard look... Groan, annoyed about that. The work the guys doing on the shell is immense, at the back it's all hand fabricated. Once finished I'll be giving him 3700 for body and paint work. The car will come with shell, early sr glass, doors, bonnet, tailgate, Daytona sr interior, no engine or box as sold the xe and was going to put a 1.3 back in, gaz coil overs, all the tank, axle, tie bars, arb all powder coated. New poly bushes and new brake line kit. New rear drums, bearings, track road ends etc. I don't think I'll get anymore sourcing an engine and nice wheels but it will be rolling with full paint and all glass in, doors built up.

[Andy]

What? why? that's a real shame

[DAFTJOHN]

I'm waiting to see what it looks like when finished but I wanted the factory look, but I think it'll have the panel overlaps gone. I've spent so much money on it and I'm at least another grand for a 1.3 engine, alloys and tyres. I wanted an original car and I could get one for a lot less than what I've spent on this. Will see over the next 3 weeks once paints finished.

[scott.parker]

John shut up!
Your never ever going to find a genuine Jamaica yellow SR for under £5.000 imo..
And not one that will be this clean, there is engines about, so grab one and be the only genuine one on here!...


:)

[Andy]

claim one back from the class 2 autograss world lol

[DAFTJOHN]

I've an engine sorted. Just waiting to see what the shell is like finished. Everything else is there...just needs a clean :)

[_Jake]

if you get stuck for an engine i have a 1.3 bottom end w/new pistons here id sell

[bazil]

You need that OCD sorted out John lol

I have a nice near standard GSI if you fancy a swap lollollol

[DAFTJOHN]

Lol I need someone to do it! I've got all the parts out an they all need a good clean

[Edd]

Selling would be a bad idea

[DAFTJOHN]

Ill get it all built and running for next summer and see what's what from there. I'll just ignore the £'s

[fossit85]

you dont want to sell this John

[Edd]

I'll just ignore the £'s

Always the best way when a Nova is concerned lol

[DAFTJOHN]

you dont want to sell this John

I don't mate but I wish the bay would have looked original.

I'm onto washing all the plastics, glass and interior now

[DAFTJOHN]

Always the best way when a Nova is concerned lol


Amen to that! Could've bought my signal green mk2 escort by now lol

[fossit85]

keep hold of the nova, original bay or not. they are about to move into the historic class for rallying. then the value will really rocket up on them. :)

[EwanG]

DO NOT SELL THE CAR! lol. If you are paranoid about the engine bay then dont pop the bonnet! The exterior will look bloody mint and I am sure anyone that looks at it will give you mega respect (more respect than a sport cause there are loads of them lol). As I said before I am a sucker for an sr and will be jealous when this little baby hits the road. If you really need the funds then sell if you have to. But if it aint about money then keep it! :thumb:

[DAFTJOHN]

DO NOT SELL THE CAR! lol. If you are paranoid about the engine bay then dont pop the bonnet! The exterior will look bloody mint and I am sure anyone that looks at it will give you mega respect (more respect than a sport cause there are loads of them lol). As I said before I am a sucker for an sr and will be jealous when this little baby hits the road. If you really need the funds then sell if you have to. But if it aint about money then keep it! :thumb:

Lol, nah not the money. Was the fact on trying to get it standard but its 30 years old so can't really get the bits easily so I'll just dial it back a bit and made it a good useable 1.3 sr....with really good body work and paint lol

[thegingerwhinger]

Just keep it ya big whore, you know youll regret it one day.

[Alex J]

how much we talking.....

[Edd]

I wouldn't worry bout the bay, it's not something you'll notice, I have a strengthening kit it mine, never bothered me

A Jamaica yellow SR is probably one of most rare Nova's, I wouldn't sell it if I were you, especially to the Axe man Meris lol

[thegingerwhinger]

lol

[DAFTJOHN]

Wheels done
http://i564.photobucket.com/albums/ss86/DAFTJOHN/Mobile%20Uploads/20140227_140847_zpsuwlx3kmc.jpg (http://s564.photobucket.com/user/DAFTJOHN/media/Mobile%20Uploads/20140227_140847_zpsuwlx3kmc.jpg.html)

[EwanG]

They look nice! I need mine done. I take it they are sprayed and not powdercoated?

[DAFTJOHN]

Cheers bud. They were blasted, coated then painted to make sure the centres matched

[istf]

W(h)ell(s) done! :thumb:

[Shamish82]

Just read this from the start cracking build mate. Will be keeping an eye on this one. Great job mate

[DAFTJOHN]

Etch on the floor
http://i564.photobucket.com/albums/ss86/DAFTJOHN/Mobile%20Uploads/20140321_120817_zpsh5yiltvv.jpg (http://s564.photobucket.com/user/DAFTJOHN/media/Mobile%20Uploads/20140321_120817_zpsh5yiltvv.jpg.html)
http://i564.photobucket.com/albums/ss86/DAFTJOHN/Mobile%20Uploads/20140321_120756_zpsjcbglztf.jpg (http://s564.photobucket.com/user/DAFTJOHN/media/Mobile%20Uploads/20140321_120756_zpsjcbglztf.jpg.html)
http://i564.photobucket.com/albums/ss86/DAFTJOHN/Mobile%20Uploads/20140321_120151_zps2ffm5lss.jpg (http://s564.photobucket.com/user/DAFTJOHN/media/Mobile%20Uploads/20140321_120151_zps2ffm5lss.jpg.html)

[7ova]

Looks good

[scott.parker]

More progress... Common want to see this finished, must be the only one in the club?

[dgbnova#1]

To be continued ...............