View Full Version : heater motor
ant_tay
08-10-08, 09:01 PM
my heater motor only works on 3 but only spins as fast as if its on 1 does anyone know how to fix it
spray the bearings with a lube like wd40
ant_tay
08-10-08, 09:03 PM
tried that
does it turn freely by hand?? if so you need to check you have feed to each of the wires with each step of the switch
ant_tay
08-10-08, 09:06 PM
yes it turns freely by hand will put a mulitmeter on it tomorrow and test it thanks
do you have a haynes so you can see which switch is which?
ant_tay
08-10-08, 09:08 PM
yeah i got one
good good. if you do have a feed to all the wires then its probably burnt out, which does happen. altho check the continuity of the earth as well
ant_tay
08-10-08, 09:12 PM
cool will do thanks
Rallyslag3
10-10-08, 12:40 AM
have you got a mk2 dash in a mk1 car?
ant_tay
10-10-08, 07:10 AM
yes i have
That was the first thing I was about to say.
You've wired the switch in wrong. It will plug right in, but you need to reshuffle the wires round - have a look in my dash swap guide in the articles, I'm pretty sure that tells you what wires go where.
Bingo
Guide (http://www.pngclub.com/forum/showthread.php?t=97606)
Heated RW/Blower
Whilst the Mk2 switch fits the Mk1 plug, it won't function properly - Vauxhall swapped some of the wires round. Chop the Mk1 plug off the loom and connect the Mk2 as follows:
MK1 BL - GE MK2
MK1 GR - GR MK2
MK1 GE - SW MK2
MK1 BR - BR MK2
MK1 BRSW - BRSW MK2
MK1 SW - BL MK2
The top two connectors are for the illumination. If you are using a mk2 plug, these can be left alone. If you are rewiring a Mk1 plug, the chop looped black wire off at the end where i connects to the main feed black wire, and connect to the blue wire.
ant_tay
10-10-08, 11:36 AM
i though BL was blue not brown
MK1 BL (brown) - GE (yellow) MK2
MK1 GR (grey) - GR (grey) MK2
MK1 GE (yellow) - SW (black) MK2
MK1 BR (brown) - BR (brown) MK2
MK1 BRSW (brown/black) - BRSW (brown/black) MK2
MK1 SW (black) - BL (blue) MK2
Yeeaaass....?
MK1 BL - GE MK2
ant_tay
10-10-08, 11:55 AM
this is what you put MK1 BL (brown) - GE (yellow) MK2
i had a look at the thread to make sure i had the colours right
Ohhh on the bit further down, forgot I'd put that in. The codes are correct, that other bit was a typo on my part which I've amended now.
ant_tay
10-10-08, 12:04 PM
ok cool thanks just making sure thats all
ant_tay
10-10-08, 12:11 PM
can i pull the pins out of the plug and put them in where they should be rather than cutting the wires
ant_tay
10-10-08, 03:20 PM
all good no its working fine thanks for your help
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.