If its single point injection yes.Originally Posted by Cle
If its single point injection yes.Originally Posted by Cle
Nova engines
Code - Capacity - Year - Output
10S - 993cc (1.0) - 1983-1993 (X-L reg) - 45bhp@5400; 50ftlb@2600
12ST - 1196cc (1.2) - 1983-1992 (X-K reg) - 55bhp@5600; 66ftlb@2200
12NV - 1196cc (1.2) - 1990-1992 (H-K reg) - 55bhp@5600; 66ftlb@2200
C12NZ - 1195cc (1.2spi) - 1991-1993 (J-L reg) - 45bhp@5000; 65ftlb@2400
13SB - 1297cc (1.3) - 1985-1989 (A-G reg) - 70bhp@5800; 75ftlb@3800
14NV - 1389cc (1.4) - 1989-1993 (G-L reg) - 72bhp@5600; 79ftlb@3600
C14NZ - 1389cc (1.4spi) - 1991-1993 (J-L reg) 60bhp@5600; 76ftlb@2600
C14SE - 1389cc (1.4mpi) - 1991-1993 (J-L reg) - 82bhp@5800; 86ftlb@3400
15D - 1488cc (1.5d) - 1990-1993 (H-L reg) - 50bhp@4800; 68ftlb@2400
15DT - 1488cc (1.5td) - 1990-1993 (H-L reg) - 66bhp@4600; 97ftlb@2600
E16SE - 1598cc (1.6) - 1988-1993 (F-K reg) - 100bhp@5600; 100ftlb@3400
C16SE - 1598cc (1.6) - 1991-1993 (J-L reg) - 100bhp@5600; 100ftlb@3400
Note 12NV figures aren't accurate as I'm sure the power is a little down whilst torque is higher over the 12ST
Last edited by Jack; 07-09-09 at 10:57 AM.
1969 Dodge Coronet Super Bee Restoration
"It'll be done when its done"
How to post images | Colour Chart | Rep | Search | CV tips
rare bit of info there cheersOriginally Posted by Jack
can anyone else verify these figures ?? as i've found this:
http://reviews.ebay.co.uk/What-engin...00000009956513
interested as i have a 1989 1.2L nova loon (F reg) i think i have the 12st
??
Why not check your engine code on your block that will tell you what it isOriginally Posted by DR Kauffman
I'd be interested to know where their figures for the 1.2's power and all engine's CC's came from. As all the info I've seen relates to the data I put up
1969 Dodge Coronet Super Bee Restoration
"It'll be done when its done"
How to post images | Colour Chart | Rep | Search | CV tips
f, fails boat on the ebay thing!
the 1.2i is 42-45bhp (same output as the 1.0)
There is the 12ST and NV, the NV was reported to have a few lbs more torque but a couple less bhp, and the ST was the other way round.... now given it was a low output engine anyway, it matters not the actual numbers .
where abouts is it on the block?Originally Posted by Connor
Sorry i didnt realise you replied, if you look at the picture below (of my dirty old 1.2 with the head removed so its easier to show you) its that flat edge on there, will no doubt need abit of a thorough clean to be able to see the code but it should be stamped on there, hope this helpsOriginally Posted by DR Kauffman
does anyone know what the c/r is on a 18E engine its a mk1 astra gte?