Page 2 of 13 FirstFirst 123412 ... LastLast
Results 11 to 20 of 129

Thread: *HOW TO* Rose jointed Linkage

  1. #11
    Senior User
    Join Date
    Sep 2003
    Location
    Basingstoke, Hampshire
    Posts
    3,118
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Cheers!
    Typical.. the same place i got the rosejoints from!
    Not cheap tho!

    Anyone know of any m10 washers that have a small outside diameter? or know of the word that might be used for such washers (ie opposite of a penny washer)

  2. #12
    Senior User Welsh Dan's Avatar
    Join Date
    Feb 2006
    Location
    Sunny Wrexham Drives: Derv barge
    Posts
    5,467
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    M6/M8 penny washers with a 10mm hole drilled in the middle?

  3. #13
    Senior User
    Join Date
    Sep 2003
    Location
    Basingstoke, Hampshire
    Posts
    3,118
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Yeah i think thats what i may do, open up an m8 flat washer. Just a pain as i dont have a pillar drill so its difficult to hold them and drill them!

  4. #14
    Senior User Welsh Dan's Avatar
    Join Date
    Feb 2006
    Location
    Sunny Wrexham Drives: Derv barge
    Posts
    5,467
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Mole grips?

  5. #15
    Senior User
    Join Date
    Sep 2003
    Location
    Basingstoke, Hampshire
    Posts
    3,118
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    il try to get a big vice!

  6. #16
    User
    Join Date
    Aug 2005
    Location
    Chester
    Posts
    773
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    is it the same for an aftermarket quickshift linkage?

    and what is the full shopping list for this job inc missalignment spacers

    ta

  7. #17
    Senior User
    Join Date
    Sep 2003
    Location
    Basingstoke, Hampshire
    Posts
    3,118
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    yes, it is. But it does mean cutting and welding the after market linkage. Im currently working on adjusting the standard linkage to make it a short shift.

    Shouldnt be too hard, just a matter of moving a few drilled holes.

    My list consisted of:

    2x female m10 rose joints (with 4 x spacers)
    2x male M12 rose joints. (with 4 spacers)
    1 x length of m10 threaded rod/studding
    2 x m10 nuts
    2x m12 bolts or studding
    4x m12 nyloc nuts
    2x m12 nuts.

    I did not use spacers in the end, i used an m12 tube to sleave which worked well and was cheaper.



    I have more photos at home, il upload them shortly.
    Last edited by loggyboy; 22-10-08 at 01:41 PM.

  8. #18
    Senior User
    Join Date
    Sep 2003
    Location
    Basingstoke, Hampshire
    Posts
    3,118
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Pics of my nearly finished linkage. it works fine, but as I mentioned, i plan on adding adjustments to change the throw distance, both side to side and front to back.




  9. #19
    ifhjdsnsdlfzjkzd
    Join Date
    Dec 2008
    Posts
    451
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    dar if i sen you a gear linkage will you make me one how much would you want to make me one

  10. #20
    User gazsnova's Avatar
    Join Date
    Mar 2008
    Location
    scunthorpe
    Posts
    365
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    what sort of interest is there of these linkages? i mean how many people would want one?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •