Page 2 of 6 FirstFirst 1234 ... LastLast
Results 11 to 20 of 56

Thread: Fitting gsi spoiler to standard mk2 boot

  1. #11
    Bzzzzz Admin Jack's Avatar
    Join Date
    Apr 2003
    Location
    Hicksville, GL
    Posts
    44,173
    Post Thanks / Like
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default


  2. #12
    P N G Adam's Avatar
    Join Date
    Nov 2003
    Location
    Stoke-on-Trent
    Posts
    30,497
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Razorjack
    google tastic ::
    I don't think nick will be using one of them for the measurements ::

    or will he :o ::

    Nice one nick :+:

  3. #13
    Member
    Join Date
    Dec 2004
    Posts
    30
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I thought it would be easy but you've scared me about putting it on myself now :P Measurements would be useful.

  4. #14
    3 1/2 rods.
    Join Date
    Feb 2004
    Location
    Lancaster Drives : 1.6 8v T40
    Posts
    5,975
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    i wont be using a level - That spanner is a ponce, the level doesn't even look level - thus meaning he's leveling unlevelly

    First, was to rip it off and add it to the pile




    anyway, here is is = note my little shit CAD drawing - yes it really did take me 5 seconds



    Along the top are some additional dimensions - use these to check the position of your holes once you have done the step below !

    EXTERNAL DIMENSIONS

    W - point A 700mm
    W - point B 1240mm

    X - point A 895mm
    X - point B 970mm

    Y - point A 965mm
    Y - point B 895mm

    Z - point A 1245mm
    Z - point B 695mm

    INTERNAL DIMENSIONS

    W - point A 700mm
    W - point B 1230mm

    X - point A 890mm
    X - point B 960mm

    Y - point A 960mm
    Y - point B 890mm

    Z - point A 1230mm
    Z - point B 700mm


    ADDITIONAL DIMENSIONS

    top of tailgate - W = 60mm
    top of tailgate - X = 61mm
    top of tailgate - Y = 60mm
    top of tailgate - Z = 57mm

    As you can see, the CENTER of each hole is measured diagonally back to corner B and corner A. Use a soft material tape measure, and push it flat onto the shape of the tailgate and measure.

    The idea is that, the ends of the lines will only meet at one certain point.

    Get a mate to help you, and when you've got the soft tape to the right length, use a pen to draw an arc as you move the tape in a circular motion ! Or you could use some string cutt to the right length with a pen tied on the end.

    This way you'l construct an ARC from point A and point B, these arcs will only cross in one point, This is the point where the hole should be drilled. It's basically like using a pair of compasses - but obviously this is a substitute

    To cross reference this, i have included some additional dimensions,from the side and above. use these to check the position of the diagonals. You may have to "split the difference" but they should all line up in a straight line. I have provided the measurements from the same corners but on the inside of the tailgate. As you can see the measurments are what you'd expect, the far left hole mirrors the far right hole e.t.c

    here are some pics giving the points where i measured from.





    On the corners, i measured from the very tip of the curved edge. Obviously i held it tight and flush to the tailgate, but this is just a demo pic.



    I layed the tape down paralell near the hole, and measured from the edge of the tailgate . Then i measured between the centres of the holes.

    REMEMBER THE MEASURMENTS ARE TO THE CENTRE OF EACH HOLE. the DIAMETER of each holes is roughly 8mm.

    Don't be hesitant to ask, it's very very simple the hardest bit to understand is about the two arcs really - it's all called triangulation. Don't follow this if you don't like, but i'm confident it should work nicely !

  5. #15
    P N G Adam's Avatar
    Join Date
    Nov 2003
    Location
    Stoke-on-Trent
    Posts
    30,497
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    :o right, wheres my printer ::

    Thanks a lot nick.
    Mods-I think that much effort deserves to be made into a guide on How to fit a GSI/SRI spoiler :wink:

    Nick-You have got a glacier white spoiler :evil: and i have just spent today spraying mine, badly with cans.

  6. #16
    3 1/2 rods.
    Join Date
    Feb 2004
    Location
    Lancaster Drives : 1.6 8v T40
    Posts
    5,975
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    ooh i have two if you look at the pile !

    i've thought of an easier way to do the arcs.

    get two peices of string, cutt them both to the length of the dimensions to point A and point B then holding one end at point B and the end of the other one at point A. They should meet in one place only - It's another way of doing it without drawing the arc. (you'l need a mate to do this with you)

    just bear with it, as it may not come to you as easily as me, as i have to do this for my job you see - The measurments should be a really helpful guide tho .

  7. #17
    Bzzzzz Admin Jack's Avatar
    Join Date
    Apr 2003
    Location
    Hicksville, GL
    Posts
    44,173
    Post Thanks / Like
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default

    ...and that's why Nick is Nerd Of The Week ::

    Very good guide tho.... possible sticky or link in tech guides stick in the Tech forum? (yes I know its styling but the amount of maths Nick's put in there you need a technical degree to follow it :

  8. #18
    3 1/2 rods.
    Join Date
    Feb 2004
    Location
    Lancaster Drives : 1.6 8v T40
    Posts
    5,975
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    it's hardly complicated, you do this kinda thing at secondary school

    8) 8) 8) 8) i think it should be on the homepage

  9. #19
    NW BOYS Club Member Riggy's Avatar
    Join Date
    Jul 2003
    Location
    United Kingdom
    Posts
    11,735
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    ^^^ pmsl a link on the homepage "HOW TO FIT A GSI SPOILER" (WARNING MATHS DEGREE NEEDED LOL)

    nice one nick i might actually fit mine soon then ::

  10. #20
    3 1/2 rods.
    Join Date
    Feb 2004
    Location
    Lancaster Drives : 1.6 8v T40
    Posts
    5,975
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    - you never know, i may actually get round to doing mine as well

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •