Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 32

Thread: Gte engine cutting out & kangarooing

  1. #11
    Senior User
    Join Date
    Sep 2005
    Location
    brotton , saltburn by the sea
    Posts
    1,877
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    A vac leak would usualy cause a judder lower down the revs

  2. #12
    Senior User
    Join Date
    Aug 2008
    Location
    blackpool
    Posts
    3,414
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Will give it another check cheers.

  3. #13
    Supernova Club Member millworm's Avatar
    Join Date
    Sep 2012
    Location
    Sutton, Surrey
    Posts
    3,752
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    No vac hoses off the manifold?

  4. #14
    Senior User
    Join Date
    Aug 2008
    Location
    blackpool
    Posts
    3,414
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I did check them but will do again to rule them out.

  5. #15
    Senior User
    Join Date
    Sep 2005
    Location
    brotton , saltburn by the sea
    Posts
    1,877
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Check the one way valve thing as well on the pipe to the servo . Mine started passing air through and i noticed the car drove fine after i had pressed the brake . Was a long 200 mile drive home dabbing the brake ever couple of minutes but it made it

  6. #16
    Senior User
    Join Date
    Aug 2008
    Location
    blackpool
    Posts
    3,414
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Will do cheers

  7. #17
    Senior User
    Join Date
    Aug 2008
    Location
    blackpool
    Posts
    3,414
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Still doing this. I've checked all vac pipes the inlet pipe the one way valve. Any other ideas??

  8. #18
    Senior User
    Join Date
    Aug 2008
    Location
    blackpool
    Posts
    3,414
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    The engine starts fine idles fine from cold one up to temp idle drops to low and cuts out. It will continue to start but then cut out when hot. One cooled a little it's fine and idles normaly. Any ideas ??

  9. #19
    Senior User
    Join Date
    Sep 2005
    Location
    brotton , saltburn by the sea
    Posts
    1,877
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Bit of a bodge but a mate used to have to do this with his m5 . When its hot and it cuts out try tipping ice cold water all over the cts until the area is cool if it fires up n runs its a problem there .

  10. #20
    Senior User
    Join Date
    Aug 2008
    Location
    blackpool
    Posts
    3,414
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Lol will try it. I've fitted a new genuine cts sensor no change. It's annoying me to say the least.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •