Page 3 of 30 FirstFirst 1234513 ... LastLast
Results 21 to 30 of 300

Thread: Mk2 Breeze Blue project

  1. #21
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Well no swirl pot from what I can see and this is the sender so I guess it's had its tank changed.

  2. #22
    Senior User Iain's Avatar
    Join Date
    Sep 2004
    Location
    East Midlands
    Posts
    13,604
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    If they're the same internally then I guess you can use either for a carb!

    No refunds.

  3. #23
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Today I got my new fuel tank to neck breather hose and a couple of aftermarket side repeater kits from euro car parts. These seemed a lot cheaper than what people where asking for for 2nd hand ones.



  4. #24
    Senior User
    Join Date
    Jul 2008
    Location
    Unknown
    Posts
    9,635
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Eurocarparts quality isn't as good since it was sold so I prefer genuine

  5. #25
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Well I was hoping to pick up a good used set but cannot justify paying £15 to £20 for them. I will be in the market for a mk2 grill and noticed they also sell a aftermarket one but cannot see any pictures of it. That's priced at £35 mind so is that going to be poor quality?

  6. #26
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default



    Looks like it will be bit of a rep after all! These are in very good condition and are in keeping with the car so went for them, was going to go for a digi but the prices are just stupid these days.
    Also got hold of a 1.3 inlet and dizzy from Josh so very happy, getting all the important parts now.

  7. #27
    User
    Join Date
    Dec 2011
    Location
    Fife,Scotland
    Posts
    1,138
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I can't see the side repeaters you bought front the euro car parts on their site?

  8. #28
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Still there, just checked. Under electrical and then indicators. That was using my reg tho

  9. #29
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    So just a small update from last weekend. Decided to get the front end running gear stripped off the shell. Looks like it needs a rub down and few coats of paint to freshen up. Have found that the lower arms have been strengthened by the previous owner so helpful if i decide to upgrade later down the line.



    Having problems with 2 of the nuts on the anti roll bar clamps as they are seized on and rounded off!!

  10. #30
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Also after having to dig out the impact driver I got the fuel filler pipe out. Again well corroded but should come up fine.



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •