Page 23 of 30 FirstFirst ... 132122232425 ... LastLast
Results 221 to 230 of 300

Thread: Mk2 Breeze Blue project

  1. #221
    Dr Sideways
    Join Date
    Oct 2006
    Location
    SE LONDON/KENT/ESSEX BORDERS
    Posts
    813
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Not a fan of those filters, look into the corsa mod with the little round airbox, pipe and filter instead.



    Always run a clear inline fuel filter in the bay as easy way to visually check


    Sent from my iPhone using Tapatalk

  2. #222
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Not sure it will fit the Weber tho without an adapter? I run a clear inline filter going to pump which looks clean. I’m more concerned the hose from the pump to carb is at at fault? It runs above the inlet so may get warm through use. The only way to explain the debris in the Weber filter.

  3. #223
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    So this has taken me just over a month to get running right again.
    Changed the fuel pump, re routed the fuel lines to carb away from heat, through a filter king fpr and rebuilt carb adjusting the float gap.
    Seems that the float/ fuel level could have been my problem.
    My air filter is currently removed as I’m not sure if it’s starving air to the carb.
    Heat generated from this block has always been high even tho the temp shows fine.
    I’ve heat wrapped the down pipe today so hoping to see some improvements.
    I’ve also fitted my new rocker cover and got some new hoses to link it to the breather separator. Plus the new vacuum hose to replace the recycled washer hose one I had.
    Just need to polish the oil cap and replace the bolts.



    Sent from my iPhone using Tapatalk

  4. #224
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    So got some shiny bolts finally for the rocker cover and did a bit of polishing on the oil cap a few weeks back to clear the rust.



    Also fitted 2 of the centre caps I have so far for these wheels. Need to find another pair but one of the wheels has a bloody snapped bolt in the centre cap bolt hole.






    Sent from my iPhone using Tapatalk

  5. #225
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    So thanks to Stuart aka H15 NVA he supplied me with a parcel shelf for my Nova.
    It had holes cut into it for 6x9 speakers and I was just going to get some to fill the holes.
    I decided that the ice isn’t high on my list of things so I reinforced the shelf by bonding some MDF on and I got some material samples to completely re trim the top and underneath.
    These are the best 2 I’ve found so will probably go with them.
    I also picked up some new rubber supports (not nova tho) so hopefully look original when it’s done.




    Sent from my iPhone using Tapatalk

  6. #226
    Senior User Club Member
    Join Date
    Apr 2003
    Location
    South Wales
    Posts
    6,566
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I have a mint shelf you can have matey. Although I don't fancy posting! If you're off to any shows that I can bring it along to, let me know!

  7. #227
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Will F View Post
    I have a mint shelf you can have matey. Although I don't fancy posting! If you're off to any shows that I can bring it along to, let me know!
    Thanks Will, Il be in touch if I do. If this one doesn’t work out I’m not at a big loss.

  8. #228
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default



    Front end lowered today on the Spax shocks and springs, believe them to be 40mm. Hopefully these won’t rub on any large bumps. Just need to do the rear springs as I’m already running the shorter Spax dampers.


    Sent from my iPhone using Tapatalk

  9. #229
    Supernova Club Member millworm's Avatar
    Join Date
    Sep 2012
    Location
    Sutton, Surrey
    Posts
    3,752
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Gonna go for some smaller profile tyres?

  10. #230
    Club Member Club Member
    Join Date
    Jul 2008
    Location
    Greenhithe
    Posts
    1,614
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by millworm View Post
    Gonna go for some smaller profile tyres?
    Wasnt going too. These are 50s so thought they would be more than suitable.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •