I was just reading a post that explained you use the nova barrel on the Corsa column. http://www.pngclub.com/forum/showthread.php?147161-Fitting-EPAS-Power-Steering/page2
Type: Posts; User: therealnovaboy; Keyword(s):
I was just reading a post that explained you use the nova barrel on the Corsa column. http://www.pngclub.com/forum/showthread.php?147161-Fitting-EPAS-Power-Steering/page2
Has anyone used a z16se gasket on a c16se?
would i be right in thinking the z16 uses a steel gasket?
Id have thought they would be interchangeable but look like the holes are slightly...
anyone had issues fitting them. im fitting a tyre that is 195 45 15. and at the minute is on a 6j rim et49 and using a 3 mm spacer clears the coilovers by 3 mm. arches are about 5 mm away front and...
anyone had issues fitting them. im fitting a tyre that is 195 45 15. and at the minute is on a 6j rim et49 and using a 3 mm spacer clears the coilovers by 3 mm. arches are about 5 mm away front and...
As per title. Email me on therealnovaboy@hotmail.com
Can anyone tell me the distributor cap types for a nova gte. Is there only one type? I have an orange dist cap with 4mm pins for the leads. Is there another type of hall distributor with bigger lead...
Great build always worth a read same with your gold one. Got me looking at getting a vxr meriva for the mrs.
Was wondering and thought you could help me. do the vxr seats still fold into a...
I can't see it as a huge issue tbh. 1 mm either side should pull in when you tighten the bolt. It'll probably spring back 1 mm when you take it off again.
as long as long as the bolt is tight and...
I just walked up 12 flights of stairs. maybe tomorrow ill walk back down instead of using the lift.
Yes that will work however you will need to use nova shafts. corsa shafts are longer.
1.2 on a single carb would be faster than 1.4spi with the right ecu never mind with the wrong one.
PNG doesn't charge for full stops you know.
You probably could run a c14se on single point injection but it defeats the purpose of searching for one. 1.4 Spi is almost as pants as a 1.2spi. You...
It has extra mounting points on the side of the strut tubs.
Their is a loom and ecu on eBay. Might be easier to get them separate.
http://i1216.photobucket.com/albums/dd375/therealnovaboy/Mobile%20Uploads/86BB440E-7515-4878-8F05-EBD122674C5C_zpsijphc59q.jpg
there was one on ebay the other day couldn't work out if it was a hockly one or a copy. looked quite good and was around £300 if I remember rightly. may have been a corsa one but was adjustable and...
Make it so that you can still fit it between the legs of an engine crane. youll kick your self if the engine crane cant get far enough in to lift the car on and off the spit
optimum pivot...
google "nova rally build manual" and youll get a PDF with the drawings at the back
the offset is dependant on the width of the wheel. a 7 inch wheel with et 49 will rub but a 6 inch wheel with et 49 wont. a 6 inch wheel with a 47.5 offset will probably rub.
If you use an offset...
you need a cradle to hold the curve of the piston with a hole in the middle to let the pin push through. you need a hydraulic press, at the point you think its not going to move it pops and pushes...
good luck finding a pilbeam ARB. harry hockley do some pilbeam copys but not a rear ARB
ARBs are just a substitute for spring rate - without effecting suspensions conformance over uneven ground.
ARs - reduce roll
Springs - allow the wheel to maintain wheel contact over uneven...
its more ore likely to be full lift at around 115 deg ATDC. I would doubt the standard pistons need pocketed.
Is it 12 mm lift at TDC?
I thought there only was one mark on the alternator pulley. The cam timing is set using the mark on the timing belt bottom pulley. The ignition timing should be set using the notch on the alt belt...