Search:

Type: Posts; User: Peredur; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    341

    16SE Performance Head

    Looking for a worked 16SE head ideally with +1mm valves or similar. Ideally looking for a Blydenstein B+ spec head.

    PM me
  2. Replies
    4
    Views
    588

    I'd be very interested to see photos of this...

    I'd be very interested to see photos of this build progressing thanks.
  3. Replies
    4
    Views
    588

    Are your 40/32.5 ones from Risse I take it? I...

    Are your 40/32.5 ones from Risse I take it? I assume that you'll need offset guides for the 41.7/33.7

    I am considering using 41.8 inlets from the C20NE maybe keeping std exhaust valves
  4. Replies
    4
    Views
    588

    1.6 8v Big Valve Head

    Wanted a 1.6 8v big valve head, Blydenstein ideally but will consider anything with REC valves or 39/32mm valves
  5. Replies
    7
    Views
    900

    I'm putting Wilwood Dynalites on a corsa 240x20mm...

    I'm putting Wilwood Dynalites on a corsa 240x20mm disc under 13's, but I'm getting an engineer to make up some brackets for them and they'll only go under Revolution RFXs.

    Otherwise it looks like...
  6. Replies
    7
    Views
    747

    Right, to clear things up. I've had the upright...

    Right, to clear things up. I've had the upright (hub) machined out to take the audi whee bearings. What I'm after is, will the astra drive flanges work having only reduced the diameter of the step on...
  7. Replies
    7
    Views
    747

    Big Block Hub Machining

    I'm going to be fitting big block hubs to my nova to accomodate the larger shafts etc. and I've had the uprights opened out, got the bearings and flanges ready to go.

    For the machining of the...
  8. Replies
    87
    Views
    16,796

    Update on the helmet situation: Helmet...

    Update on the helmet situation: Helmet clears!........ But the top of the helmet is higher than the top of the cage :( So the ralis will be being re-done. Thanks to all who spotted it, I would have...
  9. Replies
    87
    Views
    16,796

    Cool, I'll check with my lid on next time I'm...

    Cool, I'll check with my lid on next time I'm down in the garage. Like I say, the seating position is nice where it is (could be a tad lower, but not enough to warrant re-doing the rails). We'll see!
  10. Replies
    87
    Views
    16,796

    Good point, I'll take my lid with me next time...

    Good point, I'll take my lid with me next time I'm there. Thanks for that
  11. Replies
    87
    Views
    16,796

    I think they look worse in the photo. They're...

    I think they look worse in the photo. They're positioned quite nicely IMO, and the nav side one is quite deep so you sit very low within the seat. TBH, the one on my side is fine for me as if it were...
  12. Replies
    87
    Views
    16,796

    Long overdue progress update! Got a hold of a...

    Long overdue progress update!

    Got a hold of a pair of ex-Prodrive WRC Sparco Carbon buckets and couldn't pass on them, got them back home and mocked up - it'll be cosy in there to say the least!...
  13. Replies
    87
    Views
    16,796

    The ideal position would've been behind the...

    The ideal position would've been behind the navigator's footrest but with the impending rule changes it would be stupid to put it there and have to move it when I apply for an MSA logbook.
    There is...
  14. Replies
    13
    Views
    3,050

    Oil Water Brake Fluid Tools Jack Axle Stands...

    Oil
    Water
    Brake Fluid
    Tools
    Jack
    Axle Stands
    Driveshafts?
    Torque Wrench
    Tyre Pressure Gauge
    Compression Tester
  15. Replies
    87
    Views
    16,796

    Thanks :thumb: I believe that this Lucas one...

    Thanks :thumb:

    I believe that this Lucas one is the same dimensions as a RedTop20 (or 25) and the equivalent Odyssey. If it turns out that I need a higher capacity battery then we may need some...
  16. Replies
    87
    Views
    16,796

    Care to elaborate? O/S front would be heavier...

    Care to elaborate?

    O/S front would be heavier wouldn't it, with the engine over on that side. Also, if you're having a jib at the battery placement then I chose there as it's accessible and...
  17. Lightened & balanced standard jobby with a paddle...

    Lightened & balanced standard jobby with a paddle clutch
  18. Replies
    2
    Views
    528

    Got an AST3 Kent Cam here that would fit, might...

    Got an AST3 Kent Cam here that would fit, might be a bit too much for road use
  19. I've got one for sale with an uprated clutch if...

    I've got one for sale with an uprated clutch if you're still looking
  20. Replies
    6
    Views
    622

    Might have a pair, I'll PM you if I find them ...

    Might have a pair, I'll PM you if I find them

    Are they the same as just the standard base pull handles?
  21. Replies
    87
    Views
    16,796

    Been a while since I updated this, managed to get...

    Been a while since I updated this, managed to get some progress done at the weekend following buying a new welder (CWS BestMig 160i - top bit of kit)

    Popped in to see my machinist/engine builder...
  22. Replies
    3
    Views
    648

    Bilsteins are just about the best fixed rate...

    Bilsteins are just about the best fixed rate damper you can get. After that you're looking at AVO's or Gaz for adjustables but TBH, taking a leaf from Pro-tec and Hockly, they go for Bilstein and the...
  23. Replies
    87
    Views
    16,796

    Managed to get some progress done Finished off...

    Managed to get some progress done

    Finished off the lightened handbrake with cylinder bracket:
    ...
  24. Replies
    1
    Views
    514

    Found it, twas 8vcraig all along Here it is in...

    Found it, twas 8vcraig all along

    Here it is in case its of any interest to anyone:

    http://www.pngclub.com/forum/showthread.php?187805-Craig-s-Xe-track-Nova/page9
  25. Replies
    1
    Views
    514

    Gauge Modification Thread

    Don't know if anyone can help but I'm looking for a thread and I can't remember for the life of me who's it is.

    Basically, someone's taken a gauge cluster, cut the plastic "lens" to leave a nice...
Results 1 to 25 of 468
Page 1 of 19 1 2 3 4