Search:

Type: Posts; User: marc69; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    0
    Views
    864

    Any 32/34 Weber gurus?

    I have tried putting a 32/34 on my 1.3. It runs fine on the pierberg so engine etc are good.

    After fitting and it idling really badly I spent time making new gaskets, making sure all...
  2. Replies
    0
    Views
    9,207

    wiper motor wires

    Can anyone tell me what each wire on the wiper connection does please? This connection I have is from a Corsa B but hopefully the same as a Nova. Brown, Black (with a purple stripe), White, Yellow...
  3. Replies
    3
    Views
    1,252

    I have two GTE seats that are the same fitment...

    I have two GTE seats that are the same fitment but I think it is called laser pattern. Mine are ok, need a few plastic clips etc but can't get a photo just now as they are in storage.
  4. Replies
    6
    Views
    1,934

    I think the switch just has one screw and pulls...

    I think the switch just has one screw and pulls off. It is in Haynes.
  5. Thread: Weber 32TL

    by marc69
    Replies
    5
    Views
    9,754

    Even if the ignition advance sticks it would just...

    Even if the ignition advance sticks it would just idle too fast however put some oil in the dizzy and suck the advance pipe to make sure it moves back and forth freely. Who has tuned the carb? Have...
  6. Thread: Weber 32TL

    by marc69
    Replies
    5
    Views
    9,754

    The weber 32 is brilliant on the 1.0 but if dirt...

    The weber 32 is brilliant on the 1.0 but if dirt gets in the internal tubes it is very difficult to get it going properly again. It might be an idea to remove it, spray wd 40 through the internal...
  7. Replies
    4
    Views
    13,243

    No need to remove belt and pulleys on a carb 1.2....

    No need to remove belt and pulleys on a carb 1.2. I changed the rear pulley cover on my injection one so no need to remove it all next thermostat change.
  8. Replies
    4
    Views
    10,388

    Yes, downpipe to manifold. Well what I did today...

    Yes, downpipe to manifold. Well what I did today was to use the studs that are used for the manifold to block as they are longer and the nut will turn when the stud runs out of thread in the...
  9. Replies
    4
    Views
    10,388

    I went out just now and put new bolts in ( the...

    I went out just now and put new bolts in ( the old ones had flattened threads), cleaned up the surfaces. the new bolts seem to tighten (I didn't try to over tighten) but the leak is still from the...
  10. Replies
    4
    Views
    10,388

    re threading exhaust manifold

    I recently bought a 1.3 exhaust manifold but when fitting it the thread nearest the engine and driver for the exhaust were threaded, so I tightened as much as seemed best and use gun gum. It has held...
  11. Replies
    0
    Views
    6,716

    1.3 exhaust manifold

    Has anyone got a OHC 1.3 Exhaust manifold (the one that attaches to the twin down pipe) to sell and post to Aberdeen?

    I think it should be the same as mk2 astra 1.3 also.
  12. Replies
    6
    Views
    10,634

    Set them how I like the car, it's just a road car...

    Set them how I like the car, it's just a road car so not needing anything too severe.
  13. Replies
    6
    Views
    10,634

    Thanks, I jus put a coilover kit on the car, no...

    Thanks, I jus put a coilover kit on the car, no MOT issues and it handles fine with reasonable road manners.
  14. Replies
    6
    Views
    10,634

    Thanks, that's what I thought from what you said...

    Thanks, that's what I thought from what you said regarding the front but just wanted to check, at least I have a use for the rear shockers. I assume using these shockers at the rear won't cause...
  15. Replies
    6
    Views
    10,634

    koni rear shockers.

    I have a set of Koni rear shockers, if I put them on with standard SR rear springs will it make the handling better or create issues?
  16. Replies
    4
    Views
    950

    Thanks, that makes sense. I do have coilovers but...

    Thanks, that makes sense. I do have coilovers but also have a standard SR set so might just go with that.
  17. Thread: Koni shocker

    by marc69
    Replies
    0
    Views
    9,736

    Koni shocker

    I need a Yellow Koni (not adjustable type) front strut shocker. It is the type that has Koni written on a triangle if that makes sense, I can't find it new anywhere so assume it is an older type.
  18. Replies
    4
    Views
    950

    Were the shocks with 40mm springs worse than...

    Were the shocks with 40mm springs worse than standard suspension?
  19. Replies
    4
    Views
    950

    Shocker and springs.

    Are standard front strut shockers fine to use with springs that are 40mm shorter in height on a small block car?

    My reason for asking, the top of the passenger side of mine wasn't right and is...
  20. Thread: Heat Gun....

    by marc69
    Replies
    10
    Views
    15,285

    I used it, patchy and not as good as a very thin...

    I used it, patchy and not as good as a very thin layer of oil (or if you are wearing protective gloves) burnt oil seems to last forever.
  21. Thread: belt direction

    by marc69
    Replies
    4
    Views
    858

    Yes, I'll change it tomorrow. The one that was on...

    Yes, I'll change it tomorrow. The one that was on the car was on this way so probably ok but might aswell change it round, better safe than sorry. Thanks
  22. Thread: belt direction

    by marc69
    Replies
    4
    Views
    858

    Thanks, I have never noticed arrows or thought of...

    Thanks, I have never noticed arrows or thought of direction on a new cambelt before, something new everyday.
  23. Thread: belt direction

    by marc69
    Replies
    4
    Views
    858

    belt direction

    I have just put a new square toothed cambelt on my 1.3 with the arrows on the belt facing the same way as the old belt.
    The arrows are anti-clockwise but I think the engine turns clockwise?

    Does...
  24. Replies
    2
    Views
    3,549

    Thanks

    Thanks
  25. Replies
    2
    Views
    3,549

    1.3 accelerator cable

    I am looking for a throttle cable for SR which is running the pierberg 2e3 if anyone has one for sale please?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4