Search:

Type: Posts; User: mowgli; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    3
    Views
    762

    It’s in chapter 13. They show you the torque...

    It’s in chapter 13. They show you the torque figures for the things that are different to the 1.2/3/4 ones
  2. Replies
    1
    Views
    710

    Hi it depends on which 1.4 because of the...

    Hi it depends on which 1.4 because of the breather locations
  3. Replies
    3
    Views
    762

    All Haynes books have them the 1.2,1.3,1.4 & 1.6...

    All Haynes books have them the 1.2,1.3,1.4 & 1.6 have the same bottom end torques.
  4. Mostly, running in is bullsh!t and has been for...

    Mostly, running in is bullsh!t and has been for decades.

    is it getting decent power? Or are you still tickling around in it?

    i’ve literally only ever taken it easy for a day or so because if...
  5. Replies
    3
    Views
    1,639

    https://www.pngclub.com/forum/showthread.php?19859...

    https://www.pngclub.com/forum/showthread.php?198594-LHD-Corsa-to-RHD-Nova-Sport-Replica-Track-Car
  6. Replies
    4
    Views
    3,034

    It should be identical

    It should be identical
  7. Replies
    3
    Views
    5,738

    Unless it’s for classic rallying, I doubt it’s...

    Unless it’s for classic rallying, I doubt it’s worth doing anyway
  8. Thread: 1.2 misfire

    by mowgli
    Replies
    24
    Views
    16,295

    Are you using the black screw on dizzy with the...

    Are you using the black screw on dizzy with the advance retard diaphragm?
  9. Right, I’ve been Away a while, and I’m getting my...

    Right, I’ve been Away a while, and I’m getting my nova mojo back up to speed..

    you are running a c16se, on carbs, With a lumpy cam on a z16se bottom end, but what dizzy? A vacuum advance or...
  10. Dizzy timing in Haynes is for leaded, it will...

    Dizzy timing in Haynes is for leaded, it will need retarding a bit.
  11. Replies
    3
    Views
    5,738

    The build is for a rally car. It probably Meant...

    The build is for a rally car. It probably Meant blank off the top end at the cam carrier & run the crank one to a catch tank.
    the group a engine ran a harsher cam & much higher compression, so it...
  12. Should fit. the lambda sensor will need a flange...

    Should fit. the lambda sensor will need a flange making
  13. Replies
    120
    Views
    31,487

    Hi Colin, what are you thinking for the front...

    Hi Colin, what are you thinking for the front suspension?

    it basically sounds like some crazy modsports or special saloon type thing. What class restrictions on the bodywork are there?
  14. Replies
    1
    Views
    739

    Nz is square port. any of the mpi small block...

    Nz is square port.

    any of the mpi small block heads should fit as long as they have round inlet ports
  15. Replies
    7
    Views
    1,417

    From what I remember, you’ll need the front...

    From what I remember, you’ll need the front bulkhead. The wiring loom will most likely need changing too. Your best bet is a donor vehicle
  16. Replies
    1
    Views
    5,082

    I doubt any are available. Grinding down the...

    I doubt any are available. Grinding down the valve guides & using 8v big block inlet valves will give you a serious increase in flow, but grinding down the stems is do-able with a decent large &...
  17. What dizzy & cam carrier are you using?

    What dizzy & cam carrier are you using?
  18. Replies
    31
    Views
    31,551

    Did you do the Haynes book TPS bridging thing...

    Did you do the Haynes book TPS bridging thing when checking the timing? You then need to retard it for unleaded.
    def check the flexi pipe for a split.
    also look at the air inlet valve (electric...
  19. Replies
    8
    Views
    7,349

    I once sat in my car in a tyre place till they...

    I once sat in my car in a tyre place till they tracked both sides as opposed to the one because my wheel was so far off that I couldn’t drive & see my speedo on a straight road. After a stand off of...
  20. Replies
    2
    Views
    6,747

    Help needed on 1.2 spi fitment

    Hi, basically I’m planning to chuck a 1.2 spi into my mk1 whilst I take out the e16se & sort out something else to go in.
    i have the engine but need to sort out an injection loom & ecu.
    Do I...
  21. Replies
    16
    Views
    41,742

    Take the clock out, remove the main spindle &...

    Take the clock out, remove the main spindle & turn the numbers to match what you need & push the spindle back in. 5minute job
  22. Replies
    11
    Views
    12,352

    Make sure it has 1598cc on the cover Sent from...

    Make sure it has 1598cc on the cover

    Sent from my SM-G388F using Tapatalk
  23. Replies
    11
    Views
    12,352

    EBay is good Sent from my SM-G388F using...

    EBay is good

    Sent from my SM-G388F using Tapatalk
  24. Replies
    11
    Views
    12,352

    Do you have the light blue Haynes book with the...

    Do you have the light blue Haynes book with the section on E16SE in chapter 13? It's all in there

    Sent from my SM-G388F using Tapatalk
  25. Replies
    11
    Views
    12,352

    Ignition timing is & usually gets advanced way...

    Ignition timing is & usually gets advanced way too much

    Sent from my SM-G388F using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4