Search:

Type: Posts; User: jonnyd61; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    2,129

    Alternator issue I think

    Just wondering if anyone could shed some light on my issue.I am running the Nova Gsi 6 Dial clocks in C20xe when I first start the car the volt gauge seems to sit low I have to rev the car up in high...
  2. Replies
    2
    Views
    1,335

    Yes the sender is a two pin one One side plug and...

    Yes the sender is a two pin one One side plug and other side just a push on connector like off the cavs an calibras that run the oil pressure gauges
  3. Replies
    2
    Views
    1,335

    Oil pressure gauge help

    Looking for some advice on why my oil pressure gauge sits at full all the time. I?m using mk2 6 dial ones
    my oil pressure sender has two wires going to it one is the black plug (blue/green wire and...
  4. Replies
    3
    Views
    1,018

    I had to take some Material off the back of the...

    I had to take some Material off the back of the hub jobs seems a good un now
  5. Replies
    3
    Views
    1,018

    Ye fella seen it I’m guna take it back apart an...

    Ye fella seen it I’m guna take it back apart an see what I can do wit it
  6. Replies
    3
    Views
    1,018

    Meriva 5 stud problem

    Is ther anyone using meriva 5 stud front hubs I?m having an issue with the hub touching the knuckle.
    iv had the hub machined down to use nova bearing so im using the nova knuckles. Alls good when...
  7. Replies
    324
    Views
    45,357

    what did you use to fit the skirts fella ? tiger...

    what did you use to fit the skirts fella ? tiger seal ?
  8. Replies
    11
    Views
    1,790

    had a quick look and seems to being coming from...

    had a quick look and seems to being coming from some were osr upper of the tank couldn't see much to be honest. I used a small mirror an i can see two small pipes up the side im going to take the...
  9. Replies
    11
    Views
    1,790

    Today I jack it up on near side front to do some...

    Today I jack it up on near side front to do some work went abit higher then usual an noticed fuel leaking from off side rear end of tank so going to investigate in the week maybe dodgy filler neck...
  10. Replies
    11
    Views
    1,790

    It’s not only when the car is running I can rock...

    It’s not only when the car is running I can rock the car back and forth and a few seconds later there will be a strong smell of fuel in the garage but I can’t see any leaks or anything it’s like once...
  11. Replies
    11
    Views
    1,790

    No tank doesn’t look wet for what I can see .all...

    No tank doesn’t look wet for what I can see .all lines are dry an breather looks in good nik
    mybe a tank off jobby :cry::(
  12. Replies
    11
    Views
    1,790

    Bad fuel smell

    Just wondered if anyone could help I am getting a very strong smell of fuel from the car I?ve checked all the fuel lines and there are no leaks drips ect everything seems dry. When I jack the car up...
  13. Thread: 5 stud info

    by jonnyd61
    Replies
    2
    Views
    1,445

    Thanks

    Thanks
  14. Thread: 5 stud info

    by jonnyd61
    Replies
    2
    Views
    1,445

    5 stud info

    Can someone point me in the right direction for the 5 stud conversion guide
    was told there is a guide on here
  15. Replies
    15
    Views
    6,730

    still for sale ??

    still for sale ??
  16. Replies
    5
    Views
    9,463

    Yes mate

    Yes mate
  17. Replies
    5
    Views
    9,463

    Hasn’t gone one mate ?

    Hasn’t gone one mate ?
  18. Replies
    5
    Views
    9,463

    Breather on rocker cover sucking air ?

    (C20let fresh rebuild) I noticed that my breather on my rocker cover is sucking air in not pushing it out Anyone else had this problem ??
  19. Replies
    2
    Views
    7,561

    Standard bolts going to drill the rivets out

    Standard bolts going to drill the rivets out
  20. Replies
    2
    Views
    7,561

    C20let head bolts torque setting

    C20let head bolts torque setting please (nm)
    Using standard z20let head gasket
  21. Replies
    3
    Views
    5,798

    iv heard horror story's about the nylon valves...

    iv heard horror story's about the nylon valves messing up ??
  22. Replies
    3
    Views
    5,798

    Clet/xe oil pump gear

    Doing a full build on my clet was just wondering is it worth up grading the oil pump gear ??
  23. Replies
    9
    Views
    11,717

    Are standard rods good for 280-300 ??

    Are standard rods good for 280-300 ??
  24. Replies
    102
    Views
    103,425

    Do you have a link for the rad on ebay mate ??

    Do you have a link for the rad on ebay mate ??
  25. Replies
    9
    Views
    11,717

    My first C20let (advice)

    Got my first C20let just after some advice going to be doing a full rebuild hoping to use the EDS phase 2 chip just wondered what do people recommend mods to the phase 2 chip looking to hit 250ish...
Results 1 to 25 of 386
Page 1 of 16 1 2 3 4